|
|
Strain-stress analysis of gear coupling
Vondra, Róbert ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
This thesis deals with the contact analysis study of crown gear couplings during the simulation of its working conditions. The toothed coupling transmits high torque, even when the input and output shafts are misaligned due to outside tooth shape. For this reason, it is necessary to design the gear shape correctly. The inherent use of toothed couplings results in a wide range of working speeds and load transfers. This can cause several problems, if the parameters are selected incorrectly. Among the most significant of these is the generation of vibrations during gear engagement, accompanied by noise and the excessive loading of components, such as shafts and bearings. It is not possible to completely reduce uneven running, even with knowledge of the latest trends in the field of gear development. For this reason, it is necessary to eliminate the paths where the vibrations can propagate during the design itself. Inefficient and costly experiments are often used to determine the correct shape of gear teeth. For this purpose, a computational approach to describe a contact pressure on the teeth of couplings at different misalignment and loads is proposed. The model helps to understand the composition of the contact pressure during the working mode of misalignment and its behaviour within the rotation of the gear coupling. The introductory part of thesis presents the current state of knowledge of gear couplings and a description of load distribution issues, regarding the angular misalignment, torque and friction. In the following chapter, three possible approaches to the problem are described - analytical, experimental and computational. The following work offers the introduction and creation of two different computational models, varying in different tooth shape on the hub and the sleeve. Each geometry was subjected to a different load moment, a misalignment of the hub, or the rotation of the gear coupling as a whole. The main monitored parameter was the course of contact pressure in each step, when changing the degree of misalignment or the rotation of the model. Finally, three main sets of contact pressure on the teeth are presented, in connection with the reduced pressure plotted on the toothed rings. There is derivation of results and mutual comparison of each load case. The computation approach in FEM program Ansys Workbench was used to solve the problem.
|
|
|
Process fluids in machining operations
Vondra, Róbert ; Osička, Karel (referee) ; Kalivoda, Milan (advisor)
This bachelor thesis deals with a process fluids. The first part of the thesis characterizes the fundamentals of machine cutting with the use of the process liquids. Further, there are described the functions of the process fluids and the individual technological requirements placed on the liquids, along with their advantages and disadvantages. The following chapter deals with a specific range of process fluid manufacturers in the world. At the end of this thesis, a use of process fluid in practice is illustrated. CNC grinding machine was used, in order to machine the spiral shape of a micro mill.
|
|
|
Strain-stress analysis of gear coupling
Vondra, Róbert ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
This thesis deals with the contact analysis study of crown gear couplings during the simulation of its working conditions. The toothed coupling transmits high torque, even when the input and output shafts are misaligned due to outside tooth shape. For this reason, it is necessary to design the gear shape correctly. The inherent use of toothed couplings results in a wide range of working speeds and load transfers. This can cause several problems, if the parameters are selected incorrectly. Among the most significant of these is the generation of vibrations during gear engagement, accompanied by noise and the excessive loading of components, such as shafts and bearings. It is not possible to completely reduce uneven running, even with knowledge of the latest trends in the field of gear development. For this reason, it is necessary to eliminate the paths where the vibrations can propagate during the design itself. Inefficient and costly experiments are often used to determine the correct shape of gear teeth. For this purpose, a computational approach to describe a contact pressure on the teeth of couplings at different misalignment and loads is proposed. The model helps to understand the composition of the contact pressure during the working mode of misalignment and its behaviour within the rotation of the gear coupling. The introductory part of thesis presents the current state of knowledge of gear couplings and a description of load distribution issues, regarding the angular misalignment, torque and friction. In the following chapter, three possible approaches to the problem are described - analytical, experimental and computational. The following work offers the introduction and creation of two different computational models, varying in different tooth shape on the hub and the sleeve. Each geometry was subjected to a different load moment, a misalignment of the hub, or the rotation of the gear coupling as a whole. The main monitored parameter was the course of contact pressure in each step, when changing the degree of misalignment or the rotation of the model. Finally, three main sets of contact pressure on the teeth are presented, in connection with the reduced pressure plotted on the toothed rings. There is derivation of results and mutual comparison of each load case. The computation approach in FEM program Ansys Workbench was used to solve the problem.
|
|
|
Process fluids in machining operations
Vondra, Róbert ; Osička, Karel (referee) ; Kalivoda, Milan (advisor)
This bachelor thesis deals with a process fluids. The first part of the thesis characterizes the fundamentals of machine cutting with the use of the process liquids. Further, there are described the functions of the process fluids and the individual technological requirements placed on the liquids, along with their advantages and disadvantages. The following chapter deals with a specific range of process fluid manufacturers in the world. At the end of this thesis, a use of process fluid in practice is illustrated. CNC grinding machine was used, in order to machine the spiral shape of a micro mill.
|
guest ::
RSS feed.