|
|
Using simulation to predict defects in and cast Al-alloy castings
Šolc, Petr ; Bařinová, Dagmar (referee) ; Čech, Jaroslav (advisor)
The aim of this work is comparing three casting process simulation programs for porosity and microstructure prediction capabilities for die-casting. After confronting these results with experimentally measured data taken from real castings it could be said that simulation is pretty accurate for DAS microstructure prediction and hot-spot areas. Amount of measured porosity could not be compared with predicted values because specimens were not taken from the exact hot-spot areas.
|
|
|
Mg-alloy die-castings - trends in industrial
Svoboda, Rostislav ; Juřička, Ivo (referee) ; Čech, Jaroslav (advisor)
The aim of this thesis is to determine influence of porosity and shape-factor over mechanical properties, performed on cast samples from Aalen foundry (Germany), that were high pressure die casted from AZ91 D Alloy. Evaluation of these quantities was done using computer software Olympus Five. Measured values were subjected to statistical analysis in order to eliminate gross errors and determine linear dependence between mechanical properties and porosity eventually voids shape factor.
|
|
|
Evaluation of porosity in Al-alloy die-castings
Klocová, Petra ; Nová, Iva (referee) ; Čech, Jaroslav (advisor)
The objective of this diploma thesis is an evaluation of die-castings porosity, eventually the evaluation of seats with local squeeze in connection with their mechanical and structural properties. The swatches of alloy AISi9Cu3 were taken from the engine block made by Škoda Auto Company, Mladá Boleslav. To the evaluation and the comparison of the results there were the other VUT FSI Brno students´ theses used.
|
|
|
Al-alloy die-castings-trends in industrial
Rýdel, David ; Pacal, Bohumil (referee) ; Čech, Jaroslav (advisor)
The objective of this diploma thesis is to state the influence of porosity, DAS and shape factor on mechanical characteristics for the cast transmission cover made in Kovolit Modrice a.s.Which was molten from AlSi9Cu3. It was used an imaging software (Olympus Five) for classification of metallographical structures.
|
|
|
Evaluation of porosity in gravity - cast Al - alloy castings
Staňková, Markéta ; Nová, Iva (referee) ; Čech, Jaroslav (advisor)
Solving of this diploma thesis is evaluation porosity in sequence on mechanical properties from different Al alloys. Castings were made by gravity casting to the iron-mould or gravity casting to the sand. Measurements (mechanical properties, porosity, DAS - dendrite arm spacing, shape factors and sphericity) were statistically analysed and dependencies which were detected were processed to the graphs.
|
|
|
NOx production and elimination content in the flue gas
Čech, Jaroslav ; Šnajdárek, Ladislav (referee) ; Hrnčířová, Michaela (advisor)
The Bachelor thesis deals with oxides of nitrogen, resulting from the combustion process. The thesis is concentrated mainly on the description of the emergence mechanisms and on the various measures that are used to reduce their concentration. Part of the thesis is also focusing on legislation in the field of air protection, with the values of the emission limits valid for the Czech Republic and the European Union.
|
|
| |
|
|
Study of the main factors affecting quality in technological processes
Talanda, Ivan ; Nová, Iva (referee) ; Čech, Jaroslav (advisor)
The aim of this bachelor’s thesis is to theoretically describe porosity problems of casts of aluminium alloys that are made via die casting technology. The thesis is focused on influence of porosity on mechanical properties of casts. Theoretical dependencies were verified in experiment, which is based on new measured data and data witch were taken from diploma theses and science articles written by other students of the University of Technology in Brno. The samples used in experiment come from engine blocks, which were made by technology of die casting or die casting with local squeeze casting.
|
|
|
Mg-alloy die-castings for automotive industry
Hejduk, Oldřich ; Pacal, Bohumil (referee) ; Čech, Jaroslav (advisor)
The thesis dealt in the degree of the bachelor study covers Mg-alloy die-castings for automotive industry. Major destination is description properties of Mg-alloy, special properties of Mg-alloy die-castings. Experimental part of this thesis deals posibility of mensuration and calculation residual tightness on the Mg-alloy die-casting AZ91D.
|
|
|
Al-alloy die-castings for automotive industry
Havel, Jiří ; Nová, Iva (referee) ; Čech, Jaroslav (advisor)
This search is concentrated on Pressure-castings of aluminum alloys for the automotive industry. In the theoretical part of this topic is described in terms of technology for casting aluminum alloys with a focus on high-pressure casting of aluminum alloy AlSi9Cu3 and methods of detecting residual stress. In the experimental section is a sample of residual stress measurements on samples cast alloy AlSi9Cu3.
|
guest ::
