|
|
Controlled heating of Composite Material
Fajkus, Martin ; Macháň, Ladislav (referee) ; Šteffan, Pavel (advisor)
The supposed thesis considers problem of heating of composite material for outdoor application. Basement of thesis is analysis of submitted sample of composite material. Measured values of composite material were compared and evaluated and than acceptable samples were choosen for next application. Part of thesis is creation of measuring software for analysis of sample. Other part of thesis is realization of equipment of control unit for heating of composite material. Control unit makes it possible to regulate heating and to set up parameters from computer.
|
|
|
"Start&Stop" system diesel engine implementation into passenger car
Fajkus, Martin ; Drápal, Lubomír (referee) ; Rasch, František (advisor)
This thesis treat of implementation „Start&Stop“ system off passenger car with diesel engine. Creates summary of adjustments and changes necessary to insertion system, further critize effect of system on ride vehicles, as on the part of komfort so and safety factor, the advantages and disavantages in urban and super urban cycle. This system has not always been ranked separately, will be there described superiors systems, on which is implemented.
|
|
| |
|
|
Modification of Naturally Aspirated Engine to Turbocharged Engine
Fajkus, Martin ; Beran, Martin (referee) ; Svída, David (advisor)
Aim of this diploma thesis is the modification of naturally aspirated engine for Formula Student competition to turbocharged version. Modification which were made are based on the issue knowledge and calculations. The input data were obtained from 3D scanning and measurements, at the school laboratories. All 3D models were created in Pro / Engineer. Input data for the computional analysis was developed in Lotus Engine Simulation. Computational analysis was performed in ANSYS by finite element method. Calculations had to simulate a piston behavior at the critical situations where the engine is under the maxiumum load.
|
|
|
The controlled heating of composites materials
Fajkus, Martin ; Havlíček, Tomáš (referee) ; Šteffan, Pavel (advisor)
Expected work solves problem of controlled heating of composite material for outdoor application. Basement of work is analysis of submitted concrete specimen of composite. Then I find out influence of direct and alternating voltage on submitted specimen and I choose method of measurement. Whereas I chose correct method of measurement, I could measure all specimens. From comparing I chose specimen of composite material, which are suitable for a next application. For chosen specimen of composite material I designed control unit for heating and tempering. The control unit was designed according to their parameter.
|
|
| |
|
|
Modification of Naturally Aspirated Engine to Turbocharged Engine
Fajkus, Martin ; Beran, Martin (referee) ; Svída, David (advisor)
Aim of this diploma thesis is the modification of naturally aspirated engine for Formula Student competition to turbocharged version. Modification which were made are based on the issue knowledge and calculations. The input data were obtained from 3D scanning and measurements, at the school laboratories. All 3D models were created in Pro / Engineer. Input data for the computional analysis was developed in Lotus Engine Simulation. Computational analysis was performed in ANSYS by finite element method. Calculations had to simulate a piston behavior at the critical situations where the engine is under the maxiumum load.
|
|
|
Controlled heating of Composite Material
Fajkus, Martin ; Macháň, Ladislav (referee) ; Šteffan, Pavel (advisor)
The supposed thesis considers problem of heating of composite material for outdoor application. Basement of thesis is analysis of submitted sample of composite material. Measured values of composite material were compared and evaluated and than acceptable samples were choosen for next application. Part of thesis is creation of measuring software for analysis of sample. Other part of thesis is realization of equipment of control unit for heating of composite material. Control unit makes it possible to regulate heating and to set up parameters from computer.
|
|
|
The controlled heating of composites materials
Fajkus, Martin ; Havlíček, Tomáš (referee) ; Šteffan, Pavel (advisor)
Expected work solves problem of controlled heating of composite material for outdoor application. Basement of work is analysis of submitted concrete specimen of composite. Then I find out influence of direct and alternating voltage on submitted specimen and I choose method of measurement. Whereas I chose correct method of measurement, I could measure all specimens. From comparing I chose specimen of composite material, which are suitable for a next application. For chosen specimen of composite material I designed control unit for heating and tempering. The control unit was designed according to their parameter.
|
|
|
"Start&Stop" system diesel engine implementation into passenger car
Fajkus, Martin ; Drápal, Lubomír (referee) ; Rasch, František (advisor)
This thesis treat of implementation „Start&Stop“ system off passenger car with diesel engine. Creates summary of adjustments and changes necessary to insertion system, further critize effect of system on ride vehicles, as on the part of komfort so and safety factor, the advantages and disavantages in urban and super urban cycle. This system has not always been ranked separately, will be there described superiors systems, on which is implemented.
|
guest ::
RSS feed.