National Repository of Grey Literature 27 records found  1 - 10nextend  jump to record: Search took 0.01 seconds. 
Selection of an optimal tool for the selected machining technology
Podstata, Jan ; Jaroš, Aleš (referee) ; Fiala, Zdeněk (advisor)
This thesis compares the properties of four types of replaceable cutting tool inserts from different suppliers during milling. The comparative factors are cutting force, material loss of the insert and the roughness of the resulting surface. The thesis is divided into two parts - a comprehensive overview of the current state of knowledge and an experiment. The first part analyzes the load, the possibility of its measurement, surface treatment of tools, milling cutters and replaceable inserts. The experiment took the form of measuring the load during face milling, measuring the surface roughness of the machined material and measuring the material loss of the inserts on an optical strain gauge. The replaceable cutting tool inserts were compared based on the performed measurements.
Force loading of milling tools during the machining process
Švec, Michal ; Trčka, Tomáš (referee) ; Polzer, Aleš (advisor)
This thesis compares the force load of two kinds of cutting tool inserts while milling. The thesis is devided into two main parts – research and experiment. The research part is focused on the theory of the force load measuring, cutting tools and cutting tool inserts and their coating. 14 grooves were made with each cutting insert while the force load was measured. Constant cutting conditions were applied. The experiment was repeated four times for each kind of cutting insert. The aim of the thesis is to determine if both kinds of inserts mill with the same force load. The results reveal that one kind of cutting tool inserts mill with the force load higher up to 85 %.
Testing and Analysis of a Broaching Machine
Dvořák, David ; Chladil, Josef (referee) ; Sedlák, Josef (advisor)
This master's thesis deals with the broaching technology. Theoretical part includes the essay about the technology, tools and machines used for broaching. Theoretical part also describes the analysis of the broaching machine testing. Practical part is focused on the collecting, comparing and analysis of the data. These data have been collected during and after the broaching process. The supplier of the new analysed broaching machine is Stenhoj Hydraulik and the older machine has been made by Arpini. The measurements show that the increased number of broached pieces influence the cutting force and the quality of the surface due to wear of the tool which has been also monitored. The measuring dimension through the ball is almost constant. In the conclusion we evaluated the economical aspect of the results.
Machining of vulcanizing molds from aluminum alloys
Kaška, Zdeněk ; Kalivoda, Milan (referee) ; Polzer, Aleš (advisor)
This diploma thesis is focused on the issue of deep drilling of vulcanization molds from various aluminum alloys. The work will describe a brief description of machined materials and tools for deep drilling, including the production of the vulcanization mold itself. Based on experimental measurements, the analysis of data and knowledge gained from deep drilling of aluminum alloys with different silicon contents will be performed. In the end, the individual components of force loads for both machined materials will be compared
Prediction of cutting forces and powers when sawing with a circular saw
Skryja, Jan ; Sliwková, Petra (referee) ; Píška, Miroslav (advisor)
This thesis deals with the cutting of steel thin-walled parts by slitting saw. Its subject is to study and test of cutting edges of slitting saws with a goal to reduce cutting forces to a minimum. The thesis is divided into the theoretical and practical part. In the theoretical part, existing knowledge about slitting saws and general cutting technology is analyzed. In the practical part testing of four slitting saws with different geometries of cutting edges during machining of chosen thin-walled part is performed. The performed measurements show that by the proper choice of the geometry of cutting edge, the cutting force can be reduced approximately by 30 %.
Manufacturing of protective sheet metal to the door
Popelář, Martin ; Císařová, Michaela (referee) ; Peterková, Eva (advisor)
The thesis deals with the design of manufacturing technology of protective sheet metal to the door from the material 17240. The blank is 0,8 mm thick sheet metal. Work is set for cold shaping of metal by means of cutting. Production on sequence shearing tool is based on series 100 000 pieces. Shearing machine LEXN–100 2 (Toma trading s.r.o.) with shearing force 1000 kN is selected for realization. The main point of the thesis is to design a cutting tool and to create a drawing documentation.
Factors affecting the quality of machined surfaces after milling operation
Černý, Libor ; Jaroš, Aleš (referee) ; Fiala, Zdeněk (advisor)
This diploma thesis deals with the final quality of the surface under variable working conditions during milling. The first part deals with the definition of qualitative parameters describing surface properties. This is followed by a brief description of the cutting resistance measurements. The thesis is complemented by experimental verification using front milling and its evaluation. The aim of the experiment is to determine the dependence of the surface quality and the size of cutting resistors under the variable working conditions of the machine that do not make a common part of the manufacturing processes.
Stiffness of Industrial Robot Arm
Vogel, Jan ; Jurčišin,, Miroslav (referee) ; Knoflíček, Radek (advisor)
Stiffness analysis of an arm of an industrial robot with linear kinematics during a drilling operation. For solving this problem are used optical scanners. Finding the optimal cutting force for drilling by criterions: minimal deformation of robots arms and, at the same time, the emerging vibration from the cutting process is also minimal.
Construction design of woodworking machinery for preparing sawn timber
Závodný, Tomáš ; Tůma, Jiří (referee) ; Šubrt, Kamil (advisor)
This thesis deals primary with design of a woodworking machine focused on woodworking technology by cutting – rip saw. The introduction to the work is get to acquainted with the material to be processed – wood, and also the search of associated machines with the same technology of workpiece processing. Next part is focused on the safety of machining on woodworking machines and the individual safety features that the machines must contain are also analyzed. From this survey, a saw model with all the necessary features is created. The conclusion of the thesis is devoted to the risk analysis of the proposed machinery and their reduction.
Production of the magnet holder
Kraval, Jiří ; Lidmila, Zdeněk (referee) ; Žák, Ladislav (advisor)
This project developed within the engineering studies of M-STG submits a proposal of a production technology of production of the magnet holder made of DC03. Based on a literary study of the problem of cutting, drawing, bending and calculations manufacturing of the component in a production die was suggested. The production die uses a normalised component and is tightened on PE 100 crank press with nominal drawbar pull 1000 kN. The conclusion of the thesis deals with the economic benefit of the suggested manufacturing technology.

National Repository of Grey Literature : 27 records found   1 - 10nextend  jump to record:
Interested in being notified about new results for this query?
Subscribe to the RSS feed.