|
|
Methods of assessing the increase in the durability of concrete products with a painted surface with a subsequent cure
Minaříková, Kateřina ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
This diploma thesis is focused on the description and summary of existing knowledge about vibro-pressed concrete products with treated surface with protective coating, that is hardering by ultravioled and infrared radiation. The theoretical part describes the production of vibro-presses products, possible wayt of finishing the surface including the description of the most commonly used materials and the methods of application and hardering of protrctive coating on the surface. Another point of the theoretical part is creating of lime efflorescence on the concrete surface and their subsequent disappearance. The experimental part of the thesis is ficused on obtaining information about the properties of the modified pavements by these techologies and comparing the acquired properties with the charakteristice of the reference pavements that do not have any protective coating on their surface.
|
|
|
Activation admixtures in concrete
Eger, Lukáš ; Hela, Vlastimil (referee) ; Hela, Rudolf (advisor)
The aim of my bachelor´s work is the summarization and focus on admixure concrete,and the active and inert admixure, which have some positive characteristies for fresh and hardened concrete. Theoretically, I tried to study the increase of their joining potential while this characteristic can be used by either chemici or mechnical way, their combination as well. I also Works on evaluetion of physically mechanical influence for fresh and hardened concrete that can up to 60 days old while the cement was partly substituted by admixure of different character.
|
|
|
Possibilities of increasing the durability of concrete products based technologies hardening their surface
Minaříková, Kateřina ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
In the last years, we focus on higher quality of surfaces in the field of vibro-pressed concrete products. Therefore, there are products with specially modified backing layer in the market where there is implemented impregnation coating on the surface that is cured by ultraviolet and infrared radiation. The primary objective of my thesis is summary of the existing knowledge about vibro-pressed concrete products that are modified by these technologies. I will especially focus on description and efficiency of using particular methods, principals of curing surfaces and other modification of concrete product’s surfaces with emphasis on its durability. There will be examined in the laboratory conditions some of the characteristics of these vibro-pressed concrete products as resistance of surfaces against water effects and chemical defrosting substances, water absorption of surfaces, abrasion resistance, slip resistance, as well as risk reduction of creating lime efflorescence on the concrete surfaces.
|
|
|
Studying the properties of vibro-pressed concrete products, with coated surface
Bednář, Patrik ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
Technology so-called vibro-pressed concrete is currently used, inter alia, also for the manufacture of concrete products such as concrete paving blocks, slabs, kerbs, masonry and other elements. Especially for products intended for the covers of the tiles have recently begin to apply their ennoble facing layers by using special methods and technologies. The objective of this bachelor´s thesis is a summary of current knowledge about vibro-pressed concrete products whose surface is finally adjusted with the coating, followed by hardening the surface. Emphasis will be put on the description of the current methods and different ways of finalization facing layers of these products.
|
|
|
Assessing the impact of the closing of paint and lacquer surfaces on the durability of concrete products
Zubkova, Ekaterina ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
This diploma thesis is focused on studying the influence of different types of surface treatments on vibropressed product. The main goal is to characterize surface treatments consisting of application of surface coatings that are hardened by infrared or ultraviolet radiation. Theoretical part gives specifications already known methods for surface finishing. Briefly describes selected types of prefabricated concrete parts and specificate the requirements for these products. It also describes used test methods. The experimental part was aimed at establishing the effectiveness of changing properties concrete products by adding coatings on their surface. This was achieved by testing the properties of concrete paving blocks with modified surfaces and testing of reference blocks that did not have any surface treatment followed by mutual comparison of the results.
|
|
| |
|
|
The research of cause of failure of concrete elements Face Block
Eger, Lukáš ; Husařík, Petr (referee) ; Dufka, Amos (advisor)
This master thesis focus on the analysis of effects that cause defects in concrete blocks. Experiences show that the defect of the blocks are often manifested in the form of cracks. Great rate of occurrence of defects is attributed to volume changes of poor quality concrete filler. The aim of this master thesis is to analyze the finding from the practical use and exploration of the requirements for the actual blocks and especially the concrete filler which is used to make monolithic structures built from these blocks. The attention will be paid to the interaction between the block and the concrete filler. Here we focus mainly on the volume changes caused by a change of moisture level and especially the cyclic moisture.
|
|
|
Methods of assessing the increase in the durability of concrete products with a painted surface with a subsequent cure
Minaříková, Kateřina ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
This diploma thesis is focused on the description and summary of existing knowledge about vibro-pressed concrete products with treated surface with protective coating, that is hardering by ultravioled and infrared radiation. The theoretical part describes the production of vibro-presses products, possible wayt of finishing the surface including the description of the most commonly used materials and the methods of application and hardering of protrctive coating on the surface. Another point of the theoretical part is creating of lime efflorescence on the concrete surface and their subsequent disappearance. The experimental part of the thesis is ficused on obtaining information about the properties of the modified pavements by these techologies and comparing the acquired properties with the charakteristice of the reference pavements that do not have any protective coating on their surface.
|
|
|
Assessing the impact of the closing of paint and lacquer surfaces on the durability of concrete products
Zubkova, Ekaterina ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
This diploma thesis is focused on studying the influence of different types of surface treatments on vibropressed product. The main goal is to characterize surface treatments consisting of application of surface coatings that are hardened by infrared or ultraviolet radiation. Theoretical part gives specifications already known methods for surface finishing. Briefly describes selected types of prefabricated concrete parts and specificate the requirements for these products. It also describes used test methods. The experimental part was aimed at establishing the effectiveness of changing properties concrete products by adding coatings on their surface. This was achieved by testing the properties of concrete paving blocks with modified surfaces and testing of reference blocks that did not have any surface treatment followed by mutual comparison of the results.
|
|
|
Possibilities of increasing the durability of concrete products based technologies hardening their surface
Minaříková, Kateřina ; Eger, Lukáš (referee) ; Hubáček, Adam (advisor)
In the last years, we focus on higher quality of surfaces in the field of vibro-pressed concrete products. Therefore, there are products with specially modified backing layer in the market where there is implemented impregnation coating on the surface that is cured by ultraviolet and infrared radiation. The primary objective of my thesis is summary of the existing knowledge about vibro-pressed concrete products that are modified by these technologies. I will especially focus on description and efficiency of using particular methods, principals of curing surfaces and other modification of concrete product’s surfaces with emphasis on its durability. There will be examined in the laboratory conditions some of the characteristics of these vibro-pressed concrete products as resistance of surfaces against water effects and chemical defrosting substances, water absorption of surfaces, abrasion resistance, slip resistance, as well as risk reduction of creating lime efflorescence on the concrete surfaces.
|
guest ::
RSS feed.