|
|
Lubricant film formation in compliant contact
Jaroš, Tomáš ; Čermák, Jan (referee) ; Nečas, David (advisor)
This diploma thesis deals with the study of film formation in compliant contact. Primary attention is dedicated to the influence of the entrainment speed and slide-to-roll ratio (SRR) on the central film thickness. Based on a research study of the available experimental methods, the fluorescence microscopy was used to achieve the aim of the work. Experiments were realized in ball-on-disk configuration. Firstly, a validation of the method was performed where the solid contact of the ceramic ball and the glass disk was analyzed. Since the measured values were in a good agreement with the theoretical prediction, a ball of NBR rubber material, which is commonly used for production of lip seals and o-rings, was subsequently used. The experimental measurements were performed under pure rolling and rolling/sliding conditions when the entrainment speeds varied in the range from 10 to 400 mm / s. A constant load of 0.2 N was applied. The measured data were then compared to the theoretical predictions for compliant contacts. The results showed that the thickness of the lubricating film gradually increases with increasing entrainment speed, which corresponds to theoretical assumption. Against expectations, evident influence of SRR on the film formation has been observed. In the last part of the thesis the measured data are confronted with previously published studies. Finally, some limitations of this study are discussed and recommendations for further improvement of the used experimental method are suggested.
|
|
|
THE BIOCHEMICAL PROCESS OF LUBRICANT FILM FORMATION INSIDE HIP JOINT REPLACEMENT
Rufaqua, Risha ; Ruggiero,, Alessandro (referee) ; Muoz, Anna Neus Igual (referee) ; Vrbka, Martin (advisor)
The dissertation thesis deals with the lubricant film formation chemistry on hip implant material surfaces with synovial fluid components. Biochemical and tribological properties of synovial fluid after joint replacement are focused, precisely on the chemical composition of the formed lubricating film and chemical structural changes of the associated constituents under mechanical loading. Nevertheless, the synovial fluid components‘ chemical structural changes after the joint replacement are rarely addressed and require further attention. Including metal and ceramics, various combination implant materials were applied within the lubricants of synovial fluid constituents separately and different model synovial fluids to reveal the biochemical reactions and frictional coefficients for understanding the possible lubrication mechanism. Raman Spectroscopic technique is manifested as the most appropriate method to explain the biochemical behaviour of synovial fluid and chemisorption on the surface of the implant material. The method is depicted presenting two different studies focusing on the chemical structure of the synovial fluid film on the implant surface and frictional coefficient measurement of the contact pair within the artificial hip joint. This latest methodological precedent also facilitates to evaluate the chemical structural change of the synovial fluid due to the tribological activity in the hip prosthesis. The thesis expounds original results concerning biotribology to increase the depth of knowledge on joint replacement procedure and to enhance the longevity of the orthopaedic implantations.
|
|
|
THE BIOCHEMICAL PROCESS OF LUBRICANT FILM FORMATION INSIDE HIP JOINT REPLACEMENT
Rufaqua, Risha ; Ruggiero,, Alessandro (referee) ; Muoz, Anna Neus Igual (referee) ; Vrbka, Martin (advisor)
The dissertation thesis deals with the lubricant film formation chemistry on hip implant material surfaces with synovial fluid components. Biochemical and tribological properties of synovial fluid after joint replacement are focused, precisely on the chemical composition of the formed lubricating film and chemical structural changes of the associated constituents under mechanical loading. Nevertheless, the synovial fluid components‘ chemical structural changes after the joint replacement are rarely addressed and require further attention. Including metal and ceramics, various combination implant materials were applied within the lubricants of synovial fluid constituents separately and different model synovial fluids to reveal the biochemical reactions and frictional coefficients for understanding the possible lubrication mechanism. Raman Spectroscopic technique is manifested as the most appropriate method to explain the biochemical behaviour of synovial fluid and chemisorption on the surface of the implant material. The method is depicted presenting two different studies focusing on the chemical structure of the synovial fluid film on the implant surface and frictional coefficient measurement of the contact pair within the artificial hip joint. This latest methodological precedent also facilitates to evaluate the chemical structural change of the synovial fluid due to the tribological activity in the hip prosthesis. The thesis expounds original results concerning biotribology to increase the depth of knowledge on joint replacement procedure and to enhance the longevity of the orthopaedic implantations.
|
|
|
Lubricant film formation in compliant contact
Jaroš, Tomáš ; Čermák, Jan (referee) ; Nečas, David (advisor)
This diploma thesis deals with the study of film formation in compliant contact. Primary attention is dedicated to the influence of the entrainment speed and slide-to-roll ratio (SRR) on the central film thickness. Based on a research study of the available experimental methods, the fluorescence microscopy was used to achieve the aim of the work. Experiments were realized in ball-on-disk configuration. Firstly, a validation of the method was performed where the solid contact of the ceramic ball and the glass disk was analyzed. Since the measured values were in a good agreement with the theoretical prediction, a ball of NBR rubber material, which is commonly used for production of lip seals and o-rings, was subsequently used. The experimental measurements were performed under pure rolling and rolling/sliding conditions when the entrainment speeds varied in the range from 10 to 400 mm / s. A constant load of 0.2 N was applied. The measured data were then compared to the theoretical predictions for compliant contacts. The results showed that the thickness of the lubricating film gradually increases with increasing entrainment speed, which corresponds to theoretical assumption. Against expectations, evident influence of SRR on the film formation has been observed. In the last part of the thesis the measured data are confronted with previously published studies. Finally, some limitations of this study are discussed and recommendations for further improvement of the used experimental method are suggested.
|
|
| |
guest ::
