|
|
Influence of selected agents on crystallization power of polylactide
Kurakin, Yuriy ; Přikryl, Radek (referee) ; Bálková, Radka (advisor)
The influence of seven additives on the crystallization ability of polylactide (PLA), melt flow index (MVR) and mechanical tensile properties was studied. Pressed plates with a thickness of 0.8 mm were tested. Selected additives added in amounts of 0.5 and 1.0% were as follows: talc, sodium benzoate, mixtures of organic salts with amorphous SiO2 and zinc stearate, metal salt, phosphate salt, and potassium salt of 5-dimethylsulfoisophthalate (LAK-301 - nucleating agent developed for PLA). Non-isothermal crystallization measurements were performed at different cooling rates (0.3; 0.5; 0.7; 1.0 and 1.5 ° C). All nucleation agents increased the MVR of PLA except talc; the largest increase (9-fold and 24-fold) was the addition of metal salt. The additives did not fundamentally change the mechanical properties. All samples were rather brittle (the most brittle with LAK-301), the modulus of elasticity was around 1.2 GPa for all samples, the strength of PLA was increased the most by the addition of 1% talc (by 12%) and the elongation at break was increased by organic salt with SiO2. All samples with nucleating agents content of 1% were amorphous (crystalline content did not exceed 2%). Thus, the addition of reagents did not support the crystallization process during rapid cooling, even in the case of LAK-301. However, LAK-301 was acting as an excellent nucleating agent at slow cooling rates (1.5 °C / min and below). The nucleation activity of the additives decreased in the following order: LAK-301, organic salt with zinc stearate, talc, organic salt modified with amorphous SiO2 and phosphate salt. Samples with sodium benzoate and metal salt were crystallizing on cooling in several steps and it was not possible to use the method of Dobrev and Gutzow to evaluate the nucleation activity.
|
|
|
Morphology of Polyamide 12 and Polyamide 11 formed at overpressure and underpressure
Bělašková, Marie ; Tocháček, Jiří (referee) ; Bálková, Radka (advisor)
In this master thesis it was studied morphology of polyamide 12 (PA12), polyamide 11 (PA11) and their blends in the percent ratios 95/5, 75/25, 50/50, 25/75 and 5/95 formed at pressure 7 MPa in a calorimeter both after continual heating and cooling and after annealing and isothermal crystallization. Neat polyamides and blends were further characterized by thermogravimetric analysis, differential scanning calorimetry at atmospheric pressure, Fourier-transform infrared spectroscopy in attenuated total refection, and X-ray diffraction analysis. The increased pressure improved level of polyamide chains ordering in crystal lamellae. Thermal annealing improved especially ordering of PA12, isothermal crystallization led to considerable increase of crystallinity, whereas PA11-rich blends supported perfection of PA12 crystals. Partial transformation of - to -structure occurred in case of neat PA12 at high pressure, the change of the chain conformation into the closer one occurred in neat PA11 without transformation of the type of crystal structure.
|
|
|
Water-cation bridges in soil organic matter
Starostová, Anna ; Komendová, Renata (referee) ; Kučerík, Jiří (advisor)
Degradace půdy zasolováním, zvyšující se teplota a následný úbytek mnonžství srážek v posledních letech vedou k rozšiřování aridních a semi-aridních oblastí (v současnosti pokrývají třetinu pevniny Země). Navíc představují globální environmentální problémy, které, pokud se nebudou správně řešit, můžou vést k vážné celosvětové krizi. V této diplomové práci jsme propojili tato témata a zaměřili se na lepší porozumění role sodných kationtů na vazbu vody v půdní organické hmotě v aridních a semi-aridních podmínkách. Náš cíl byl prozkoumat proces vzniku a stabilitu vodních molekulových můstků a vodních-kationických můstků v půdní organické hmotě, sílu vazby a množství vázáné vody v půdě za využití diferenční kompenzační kalorimetrie. Nasycení sodnými kationty bylo studováno ve dvou koncentračních oblastech. Na simulaci přirozených podmínek v půdách bylo použito nasycení vazebných míst sodnými kationty do 100% a nasycení nad 100% reprezentovalo vysoce zasolené půdy. Výsledky potvrdily význam schopnosti půdy získávat vodu ze vzdušné vlhkosti, podíl vody v půdě vzrůstal s relativní vlhkostí. Vyšší podíl vody v půdě pak způsoboval snížení síly vazebných interakcí, což bylo interpretováno jako fakt, že rovnováha mezi půdní a vzdušnou vlhkostí vede k optimální vlhkost půdy. Přítomnost sodných kationtů ve vzorcích do nasycení 100% měla na množství vody zanedbatelný vliv, ale v přesycených vzorcích umožňovala navázání většího množství vody. V přesycených vzorcích bylo také pozorováno zvýšení síly vazebných interakcí mezi půdou a vodou, což vede k její větší zádrži. Molekulové můstky byli stabilnější ve vzorcích, které obsahovaly Na+. Nejvyšší stabilita byla pozorována u 10% nasycených vzorcích, další zvyšování Na-saturace pak již vedlo k snižování stability molekulových můstků. Hlavním výstupem práce je, že tvorba vodních-kationických můstků stabilizuje půdní strukturu a že má vlyv na sílu a množství vody vázané v půdě, což představuje klíčové aspekty kvality půdy. Je potřebný rozsáhlejší výskum tohoto tématu, aby získané výsledky pomohli optimalizovat půdní manažment v aridních oblastech a také v ostatních oblastech, kde dochází k degradaci půdy.
|
|
|
Study of the influence of polyethylene terephthalate recycling on the quality of the resulting recyclate
Mach, Jakub ; Řezáčová, Veronika (referee) ; Kučerík, Jiří (advisor)
Plastics and recycling of plastics is a frequently discussed topic. The output of sythetic polymers is rising exponentially every year. In accordance with the sustainable development, development of effective recycling techniques enabling to process these huge amounts of waste and convert it back into useful material is essential. The aim of this work was to study qualitative effects of production methods, various types of recycling processes and degree of degradation of polyenthylene terephtalate on results of differential scanning calorimetry (DSC) analysis. In experimental part, analyzes of 62 regranulates of recycled PET were performed. The samples from various manufacturers differed (manufacturers use different technologies) in terms of mechanical and physico-chemical properties or additives. The results confirmed that the properties of recycled PET have an impact on thermophysical properties recorded using DSC. A simple DSC run enables distinguishing a number of fundamental qualitative properties of PET, in particular crystallinity, melting point and enthalpy, temperature and enthalpy of crystallization and glass transition temperature and in this work we show that their mutual relationship enables to estimate the quality of recycled material and the possibilities of its further use.
|
|
|
Kinetics of non-isothermal crystallization of polylactide with selected agents
Červený, Ľuboš ; Tocháček, Jiří (referee) ; Bálková, Radka (advisor)
The aim of submitted diploma thesis is the study of non-isothermal crystallization kinetics of polylactide (PLA) with selected agents (1 %) and observation of the emerging crystalline structure under polarizing optical microscope. The agents were talc, a mixture of organic salts with the addition of amorphous SiO2 (HPN 68L) and zinc stearate (HPN 20E) and LAK-301 (potassium salt of 5-dimethylsulfoisophtalate), which is a nucleating agent developer for PLA. The PLA matrix served as a reference. Non-isothermal crystallization took place on a differential scanning calorimeter at cooling rates () 0,3; 0,5; 0,7; 1; 1,5; 2 °C/min After non-isothermal crystallization, the crystalline fraction (Xc) od PLA was evaluated from X-ray diffraction analysis, and the supramolecular structure was observed after chemical degradative etching using confocal laser scanning microscope. The crystallization kinetics were evaluated by the methods of Jeziorny and Mo and the activation energy of the crystallization was determined according to the Friedmann method. All prepared materials were amorphous (Xc 40 % for up to 1,5 °C/min). However, for LAK-301, Xc decreased to 30 % already at the = 2 °C/min and it can be assumed that with increasing its nucleation activity will decrease. A spherulitic structure was observed in all samples, but the number and size of spherulites decreased with increasing and the appearance varied according to the type of agent. Both kinetic models proved to be unsuitable for materials with low Xc and the highest because the rate of crystallization did not change. With the Jeziorny method, it was possible to evaluate the kinetics only for the relative crystallinity Xt = 29–50 % and with the Mo method it was not possible to evaluate the data for the highest for PLA matrix and sample with HPN 68L. The samples with LAK-301 and HPN 68L showed the lowest activation energy.
|
|
|
CHARACTERIZATION OF WRAPPAGING FILMS BASED ON POLYETHYLENE AND POLYPROPYLENE
Bělašková, Marie ; Poláček, Petr (referee) ; Bálková, Radka (advisor)
By seven kinds of coextruded and blown packing polyethylene and polypropylene based films, which are supplied by Granitol were characterized in this bachelor thesis. The following methods were used for characterization: thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, confocal laser scanning microscopy , and scanning electron microscopy. The methods made possible to determine the composition of the films and to evaluate the degree of crystallinity.
|
|
|
Polyhydroxybutyrate modification by grafting of functional groups
Melčová, Veronika ; Tocháček, Jiří (referee) ; Přikryl, Radek (advisor)
Presented bachelor thesis deals with a characterization of the effect of chemical grafting on thermal and mechanical properties of poly(3-hydroxybutyrate). Two grafting methods were chosen, chlorination and fluorination of PHB. The aim of the theoretical part of the work was to create a complete literature review containing basic information about polyhydroxybutyrate and the latest scientific evidence about possibilities of chemical modification of this polymer. The experimental part describes the chemical treatment of the material itself, as well as preparation of samples for testing and performing the selected analysis. Chemically grafted polymers were subjected to thermogravimetric analysis to determine their thermal stability. Thermal behavior of materials was studied by differential scanning calorimetry. Also non-isothermal crystallization of samples was observed in order to evaluate the influence of the grafted halogen atom onto the nucleation activity of the polymer. Selected samples were also subjected to dynamic mechanical analysis and tensile test.
|
|
|
Properties of polyethylene blown-films dependent on their composition
Štaffová, Martina ; Poláček, Petr (referee) ; Tocháček, Jiří (advisor)
This work deals with the influence of quantity of recycled material on physical properties of blown-film. The task of this work is to prepare set of laboratory made films with amount of LLDPE granulate from 0 to 100 % with addition of LDPE recycled material and furthermore with addition of filler, calcite. The following methods were used for characterization of blown films: tensile test, differential scanning calorimetry, Fourier transform infrared spectroscopy, confocal laser scanning microscopy. The same measurements were performed also on industrial made blown-film.
|
|
|
Hydration of biochar prepared by using microwave pyrolysis of municipal sludge
Miklasová, Marta ; Komendová, Renata (referee) ; Kučerík, Jiří (advisor)
Microwave pyrolysis represents a possible solution of municipal sludge disposal. One of the final products of pyrolysis is amorphous porous carbon material called biochar, which can be used in agriculture as a soil amendment. As a rule, biochar is hydrophobic, but its addition can lead to an increase in water holding capacity. However, reasons of this improvement cannot be explained only by its high porosity. This thesis aims to contribute to the understanding the interactions between biochar and water under various environmental-relevant conditions such as direct water addition method and water adsorption from ambient air at different relative humidity. The thermo-analytical methods are common for investigation of the relationship between water and organic materials. One of these methods, differential scanning calorimetry, was used in this thesis. The first experiment was focused on measuring of melting enthalpy of freezable water in biochar pores. The results reflect the influence of pore size and properties of ice structure. The extrapolation of concentration dependence to zero enthalpy was used to determine non-freezing water (0,13–0,15 mg·mg-1 biochar), which reflects microporosity of the biochar. The second experiment was focused on the determination of evaporation enthalpy of water from biochar, which is a measure of the strength of water binding in biochar. This value indirectly reflects the mechanisms of the intake and release of water by biochar. Comparing the results for bound and pure water showed that in biochar is water bound weaker about 10–20 %. This led to conclusion that biochar binds water relatively weakly and the water exchange between biochar and soil is fast, despite the biochar hydrophobicity.
|
|
|
The influence of regranulate on structure and properties of high density polyethylene
Handlíř, Tadeáš ; Poláček, Petr (referee) ; Bálková, Radka (advisor)
The presented diploma thesis deals with the evaluation of the influence of the addition of 30, 60 and 90 % of recycled material on the structure and mechanical properties of high-density polyethylene (HDPE), where recycled material represents both HDPE from a several years old part and material multiple reprocessed by extrusion. The changes of supramolecular structure were examined by calorimetric measurement, which did not indicate degradation of the material due to multiple extrusion. Mechanical properties were investigated by tensile tests and dynamic-mechanical analysis. Both measurements showed the same trend, where the first and second pass of the material through the extruder led to improved mechanical properties, e.g. to increase stiffness, while the influence of the third and fourth passes through the extruder had not a significant effect on the mechanical properties. In terms of the structure and mechanical properties, a positive effect of the combination of material after the second extrusion passing (30%) with virgin material was recorded.
|
guest ::
