National Repository of Grey Literature 137 records found  beginprevious116 - 125nextend  jump to record: Search took 0.00 seconds. 
Analysis of switched-mode LED drivers
Stehlík, Ota ; Vyskočil, Pavel (referee) ; Kubíček, Michal (advisor)
The aim of this thesis is to design, produce and verify the operation of two different LED drivers for automotive industry, which controls the ultra-bright white LEDs. At the beginning of a brief introduction explaining the principle of operation of LEDs. Furthermore theory describes the functions of all three basic drivers involved as buck, boost and buck-boost. Based on the requirements are selected ICs suitable for this implementation, theoretically described their block diagrams including the individual diagrams and eventually these samples are made, revived and measured their parameters.
Small rotor dynamic balancer
Staněk, Michal ; Vyskočil, Pavel (referee) ; Kubíček, Michal (advisor)
Balancing of rotors is used to remove unwanted vibrations caused by uneven distribution of mass around the axis of rotation of the rotor. Operation of an unbalanced rotor may causes shortening of bearing life, fatigue of materials and deformation of shafts. This work deals with construction of a balancing machine (balancer). Because of its good properties, a soft bearing type balancer was chosen for construction. This type of balancer achieves higher sensitivity at the cost of calibration required for each type of rotor. To capture the magnitude of vibration electrodynamics sensors were chosen. To enter data and display results a microprocessor is used.
Fast Beam Current Change Monitor for the LHC
Král, Jan ; Kovalsky, Jan (referee) ; Kubíček, Michal (advisor)
Striktní nároky na systémy ochrany a zabezpečení LHC vyžadují vylepšené metody detekce rychlých ztrát částicového svazku. Rychlý proudový transformátor (FBCT) je měřicí přístroj poskytující informaci o intenzitě shluků urychlovaných částic. Tato diplomová práce popisuje vývoj nového systému ochrany LHC založeného na měření signálu FBCT. Tento systém, monitor rychlých proudových změn částicového svazku (FBCCM), měří signál FBCT v úzkém frekvenčním pásmu a počítá časovou derivaci okamžité amplitudy tohoto signálu. Tato derivace je přímo úměrná ztrátám částicového svazku. Pokud ztráty svazku překročí určitou úroveň, FBCCM přikáže kontrolním systémům zničit svazek kvůli bezpečnosti LHC. Ochrana LHC bude zabezpečena čtyřmi FBCCM, které budou instalovány do LHC v červenci 2014. Bylo zkonstruováno a testováno šest FBCCM. Jejich měřené charakteristiky vyhovují stanoveným požadavkům. FBCCM bylo vyzkoušeno laboratorní simulací reálného prostření LHC.
Touch panel controlled PLC systems for HV device control
Vlk, Jáchym ; Vyskočil, Pavel (referee) ; Kubíček, Michal (advisor)
The master thesis describes communication of PLC and touchscreen with purpose of high voltage control. The general information and framework are included. The thesis describes part of IVEP corporation development. Due to the beginning of a long-term development it is premature to come into conclusions within this master thesis. The first chapter deals with PLC and other components. The second chapter consists of matters about high voltage devices. The following chapter describes the programme part. The fourth and concluding chapter deals with the realization of the communication itself. A brief evaluation with prospects for the future is included in the conclusion.
Multichannel HD-SDI digital video signal converter
Kučera, Stanislav ; Bobula, Marek (referee) ; Kubíček, Michal (advisor)
This master’s thesis deals with the design of six channel SD, HD and 3G HD-SDI digital video signal converter to 10-Gigabit Ethernet. In the introductory part, the conception of designed device is formulated. The theoretical background is provided in four chapters, where main standards and design rules related to digital electronics’ design are analyzed. The emphasis is placed on signal integrity at high-speed interconnects. There mostly practical examples, calculations and simulations are utilized. The design part contains thorough description of main subsystems’ design, implementation of FPGA, SDI input channels and 10-Gigabit Ethernet PHY. In the final part, the first tests and measurements of the build prototype are summarized. As an example, the comparison of signal integrity simulation to measurement is provided.
Digitally controlled multi-quadrant power supply
Chytil, Jiří ; Štekl, Petr (referee) ; Kubíček, Michal (advisor)
This thesis deal with design of multi-quadrant power supply in linear and switching mode. In the case of the switching mode energy recuparation is also considered as well as optimalization of change of load response over time. Power supplies are designed as general purpose laboratory and process power supplies. Power supplies are designed so that they can be connected via galvanic insulated USB interface with a PC
Adaptive embedded data splitter
Kazelle, Kamil ; Tošovský, Petr (referee) ; Kubíček, Michal (advisor)
This diploma work aims to invent an algorithm for use of serial interface SGMII (serial gigabit multimedia independent interface) in adaptive embedded data splitter for Gigabit Ethernet standard 1000Base-T interface and also to aplicate these algorithms to FPGA circuit.
Digitally controlled electronic load
Bordovský, Tomáš ; Vochyán, Josef (referee) ; Kubíček, Michal (advisor)
This diploma thesis deals with analysis and exploration of design options, how to design and produce an electronic load. The paper discussed the possibilities of digital control. It also describes the principles of structural components and there was chosen one type variant which is designed to circuits and printed circuit boards. Moreover, the thesis also include technical drawings of mechanical parts. At the end of this paper, final soulution with measurements and parameters are presented.
Low-range high-speed optical transceiver
Pučálka, Jan ; Tošovský, Petr (referee) ; Kubíček, Michal (advisor)
The diploma thesis deals with description and design of a low-cost free-space optical (FSO) link. First, general FSO theory is discussed including their common parameters, properties and topologies. Further, optical signal sources and detectors are proposed. Finally, the selected implementation is described including its design and realization. The proposed FSO consists of two identical segments (modules) to form a full-duplex link. The FSO utilizes LED as a light source, maximum speed data rate is 100 Mb/s with 100Base-TX interface.
Control system for remote laser-induced breakdown spectroscopy
Petrilak, Michal ; Fuchs, Michal (referee) ; Kubíček, Michal (advisor)
The work deals with the design of the control electronics for measuring set-up for elemental composition analysis using remote LIBS techniques. The electronics is designed in modular way for light interchangeability and variability. It consists of several separate plug-ins; each plug-in solves its part of the problem and communicates with others over the I2C bus. The work describes the basic components and concepts; a special care is taken to describe the modules for stepper motors control and for communication with focusing lens from Canon company.

National Repository of Grey Literature : 137 records found   beginprevious116 - 125nextend  jump to record:
See also: similar author names
12 KUBÍČEK, Martin
1 Kubíček, M.
1 Kubíček, Marek
12 Kubíček, Martin
4 Kubíček, Matěj
2 Kubíček, Milan
2 Kubíček, Miloš
1 Kubíček, Miroslav
Interested in being notified about new results for this query?
Subscribe to the RSS feed.