National Repository of Grey Literature 209 records found  beginprevious176 - 185nextend  jump to record: Search took 0.00 seconds. 
Measurement of conductivity of liquids
Mašláň, Stanislav ; Havránek, Zdeněk (referee) ; Beneš, Petr (advisor)
The first part of thesis is theoretical and it is the introduction into conductometry. It defines the essential terms of this field as well as contact and contactless methods of measurement of fluid conductivity and also the influential parasitic phenomena and possibilities of their elimination. The second part is dealing with design of the contactless transformer conductivity probe. The characteristics of designed probe are verified in the practical part of the thesis. The final part of the thesis is dealing with measurement according to the defined points in the assignment. The characteristics of several contact probes are verified and also the characteristic of the contactless transformer probe, which was implemented according to the design from the second part. Outcomes of these measurements establish the suitable power supply frequencies and currents for all these probes.
Ultrasonic Anemometer
Křepelka, Pavel ; Fialka, Jiří (referee) ; Beneš, Petr (advisor)
In the first section of this document, there are described principles of the wind measuring. Anemometers can be divides by physical principles to mechanical (propeller or cup), ultrasonic anemometers and thermoanemometers. This paper is focused to ultrasonic anemometers. In the next part, there are described principles of sound propagation in the atmosphere. There are studies of measurement theory and comparing of different approaches. Completed solutions are presented in patent exploration. Afterwards, there are introduction of market research. Important parameters of ultrasonic anemometers are highlighted. Main aim of work is designing prototype of ultrasonic anemometer. Software, hardware and construct of experimental anemometer were designed. Created anemometer was calibrated in aerodynamics tunnel and results were compared with simulation output.
Gas flow measurement
Kozák, Matěj ; Uher, Miroslav (referee) ; Beneš, Petr (advisor)
This thesis deals with the problem of designing vortex flow meter for a nominal range of 40 l.min-1. It describes the problems of vortex bodies and choice of methods for detection of vortices. The thesis includes solution of various problems in the design, which were published in scientific articles or patents. The following describes the design solution vortex flow meter for the specified range, which uses ultrasonic sensors to vortices detection. The proposed flow meter is calibrated with reference flow meter and compared with commercially produced vortex flow by the TST electronics and Burkert companies, which are designed for the specified ranges.
Car speed measurement
Vořechovský, Karel ; Havránek, Zdeněk (referee) ; Beneš, Petr (advisor)
Car speed measurement using the Doppler effect
Broadband Lownoise Amplifier
Varga, Kamil ; Havránek, Zdeněk (referee) ; Beneš, Petr (advisor)
The bachelor thesis describes the problems of broadband low-noise preamplifiers and the conditions of their design, including their printed circuit board. Furthermore, the thesis considers debugging and measuring of the most important parameters of these amplifiers. All of these problems are explained on two practical solutions.
Digitally controlled AC voltage source
Dalík, Vladimír ; Čejka, Miloslav (referee) ; Beneš, Petr (advisor)
The thesis deals of microprocesor controlled instrument for measuring. In general it is about of controlling instruments and their usage in standard industry. laboratories and measuring systems. The first part contens theoretical knowledge of controlling instrument, his funtions and describes circuitry of sources of AC voltages. This part describes blocks of instrument and basis connecting in system of instrument. Each block is described with examples in praxis. Examples contents typical connecting and their problems out of view in parameters of instrumenr. In this part is whole theory of analysis and practical using separately parts of instrument. Next part is aimed at searching of interrelationship between the teoretical model of source that described by different circuits and practical connections with electronic parts. These part analyse concrete design with exactly sized parameters and connections. In last part contents describing of measuring at prototype. The appendix contains schematics and boards with electronic parts and test reports of measuring output voltage and frequency with required accuracies.
Weight-In-Motion
Kašpárek, Ladislav ; Klusáček, Stanislav (referee) ; Beneš, Petr (advisor)
This Master's Thesis deals with Weight-In-Motion (WIM) Systems. It focuses on piezopolymer-coaxial-cable-based sensors. The work contains summary of WIM sensors, methods for signal processing and evaluation provided by WIM sensors. The design of WIM station including measuring chain is also drawn out here. Basic meaurements on sample output from the sensor are carried out using formely designed amplifier. By this, its properties and suitability can be assessed.
Measurement module with simultaneous-sampling A/D converter
Křížek, Miroslav ; Beneš, Petr (referee) ; Havránek, Zdeněk (advisor)
In this work is designed programme unit for acquisition analog acoustic signlas from sensors. There is used accurate A/D converter ADS1287 by the company Texas Iinstrument with resolution of 24 bits to digitizing these signals. There is used 32-bit microprocessor AT91SAM7S64 by the company Atmel to control this A/D converter and sending digitized data to PC. This microprocessor has implemented USB interface. By force of developmental programme units whit microprocessor and A/D converter is produced programme for microprocessor in developmental setting IAR Embedded Workbench IDE 5.0 and simple aplication for PC in setting Borland C++ Builder. Both of those programs are in language C++. Rate of sampling is 26 kHz. On the basis is realized programme unit USB-ADC whit microprocessor and A/D converter.
Electromagnetic flowmeter
Dohnal, Zdeněk ; Bejček, Ludvík (referee) ; Beneš, Petr (advisor)
This thesis deals with inductive flowmeters, specifically insertion inductive flowmeters. It examines in detail a blueprint of such flowmeter, consisting of probe, electromagnet, electrodes, exciting module and evaluation of signal. Gauging of a flowmeter designed this way, measuring data, charts, evaluation and interpretation. Consequent measurement in a calibration laboratory to elaborate, evaluate and interpret the results.
HP89410A User Interface
Neužil, Jan ; Caha, Luděk (referee) ; Beneš, Petr (advisor)
The aim of this thesis was to develop user interface in LabVIEW to make typical measurements with spectral analyzer HP89410A There is introduced the theory of operation of an analogue heterodyne and a digital FFT spectral analyzer. It is explained the background of the Fast Fourier Transform. There are discussed the key settings in measuring with FTT analyzer, like window function, bandwidth, number of frequency points, or the averaging. Further is described the program, which was developed for measuring frequency characteristic by white noise and by stepped measurement. It was also made a module for measuring Signal to Noise Ratio and module for Total Harmonic Distortion. In the last part of this thesis are shown the results of processed exemplar measurements.

National Repository of Grey Literature : 209 records found   beginprevious176 - 185nextend  jump to record:
See also: similar author names
2 Beneš, P.
11 Beneš, Pavel
Interested in being notified about new results for this query?
Subscribe to the RSS feed.