|
|
Machining of vulcanizing molds from aluminum alloys
Kaška, Zdeněk ; Kalivoda, Milan (referee) ; Polzer, Aleš (advisor)
This diploma thesis is focused on the issue of deep drilling of vulcanization molds from various aluminum alloys. The work will describe a brief description of machined materials and tools for deep drilling, including the production of the vulcanization mold itself. Based on experimental measurements, the analysis of data and knowledge gained from deep drilling of aluminum alloys with different silicon contents will be performed. In the end, the individual components of force loads for both machined materials will be compared
|
|
|
A proposal and production of vacuum mold for serial production of plastic forming
Tišnovský, Jakub ; Chladil, Josef (referee) ; Sedlák, Josef (advisor)
This diploma thesis deals with the proposal and production of a mold for series production of plastic parts by vacuum forming. The thesis is divided into 2 main chapters. The theoretical part includes analysis of chip machining technology. The experimental part focuses on solving the design of the mold in PowerShape software, a detailed analysis of making of the model for casting and about making of the mold themselves. In the last part the manual completion and verification of the mold is discussed. Thesis is terminated by technical-economic evaluation, in which is discussed about production costs.
|
|
|
Combination of numerical mathematics and neural network for the model of breakout prediction
Srba, Jan ; Štětina, Josef (referee) ; Mauder, Tomáš (advisor)
This thesis deals with creation of breakout prediction model implemented via artificial neural network in MATLAB, hence it contains theoretical description of artificial neural networks and also presents how the networks were used for the breakout prediction problem. In addition, models of heat conduction through the mold wall were created and used for generating neccesary data for proper training of artificial neural network. The thesis contains proper description of used numerical methods for solving the heat conduction problems. In the thesis are presented partial results and also results of testing created artificial neural network with usage of real data.
|
|
|
Heat transfer solution of solidifying steel system with phase change with moving edge conditions
Fedorko, Tomáš ; Mauder, Tomáš (referee) ; Štětina, Josef (advisor)
Cílem diplomové práce je vytvoření 2D numerického modelu pohybujícího se řezu s proměnnými okrajovými podmínkami skutečné geometrie plynulého odlévání a chlazení předlitku v prostředí MATLAB. Model se zabývá vysoce nelineárními termofyzikálními podmínkami oceli během tuhnutí a chlazení. V práci je simulovaná nejen nelinearita termofyzikálních podmínek, ale také nelinearita při fázové změně. Fázová změna je modelovaná pomocí metody entalpie, metody zdánlivé kapacity a metody teplotního zotavení. Všechny výsledky práce jsou porovnány z více hledisek, jako např. z hlediska přesnosti, rychlosti výpočtu, nebo vhodnosti časového diskretizačního kroku pro nelineární problémy, a paralelizace.
|
|
|
The issue of biotic attack of ETICS
Těžká, Adéla ; Žák,, Antonín (referee) ; Žižková, Nikol (advisor)
This bachelor thesis deals with the issue of biotic attack of ETICS contact insulation systems. The theoretical part is focused on the individual components of ETICS, both from the point of view of materials and from the point of view of individual steps. In addition, there are organisms that cause biotic attack on facades. The practical part deals with the possibilities of testing the resistance of the surface treatment of ETICS against biotic attack, both in laboratory conditions and in the exterior.
|
|
|
Proposition of casting technology of aluminium manifolds cast by tilt method
Spáčil, Ivo ; Kaňa, Václav (referee) ; Roučka, Jaromír (advisor)
Description of the theoretical factors for casting into metal molds. For thin-walled castings it has turned out that the most advantageous method is tilt casting. Tilt casting reduces the turbulence of the melt and reaches a directed solidification. Two molds were tested and measured for the experiment. During measuring the temperature regime was established lower temperature of the pouring basin than the other parts of the mold, which could cause a many of defects. The verification of mold technology has been performed. To achieve the accuracy of the casting, it is necessary to respect the different shrinkage according to the shape of the casting.
|
|
|
A proposal of production technology of a mold for plastic covers
Halačka, Petr ; Vaněk, Zdeněk (referee) ; Chladil, Josef (advisor)
The bachelor thesis deals with machining of mold for blowing plastic packaging in cooperation with VBF Ltd. It focuses on 5-axis milling technology. It also contains descriptions of mold materials and injected materials. It analyzes the current process of mold production. It also contains its own proposal to improve (to make more effective) the production of a given block. The difference in technology used and the time difference are described in the conclusion.
|
|
| |
|
|
Production of the mold plunger
Rosa, Jakub ; Chladil, Josef (referee) ; Osička, Karel (advisor)
The meaning of the diploma thesis is to create a new mold plunger for injection mold using a suitable method according to the original mold plunger. The final mold part should meet the required surface parameters. The work is focused on the analysis of the original mold plunger and the experimental verification of suitable methods of production of the equivalent mold plunger.
|
|
|
Construction of molds for rubber molding
Bátrla, Martin ; Nohál, Libor (referee) ; Brandejs, Jan (advisor)
This Bachelor’s thesis contains the general body of knowledge related to theory of injection molds for rubber molding. There is also described a designing procedure of mold for rubber cuff which will be used as a protection against the dust and other impurities. The output is a 3D model of injection mold made in SolidWorks 2015 and 2D documentation of chosen parts.
|
guest ::
