Národní úložiště šedé literatury Nalezeno 18 záznamů.  1 - 10další  přejít na záznam: Hledání trvalo 0.01 vteřin. 
NANOCERIA PREPARED BY ELECTRON BEAM EVAPORATION
Pizúrová, Naděžda ; Hlaváček, A. ; Kavčiaková, Zuzana ; Roupcová, Pavla ; Kuběna, Ivo ; Buršík, Jiří ; Sokovnin, S. Y.
Cerium oxide nanoparticles (nanoceria) are currently one of the most investigated nanomaterials because of their attractive properties used in biomedical applications, catalysis, fuel cells, and many others. These attractive properties are connected with the Ce3+ and Ce4+ valency state ratio. In the nanoparticle form, cerium oxides contain a mixture of Ce3+ and Ce4+ on the nanoparticle surfaces. Switching between these two states requires oxygen vacancies. Therefore, nanoceria's inherent ability to act as an antioxidant in an environmentally-dependent manner and a “redox switch” to confer auto-regenerating capabilities by automatically shifting between Ce4+ and Ce3+ oxidation states is significantly affected by surface morphology. Regarding this demanded behavior, we aimed to characterize synthesized nanoparticle surface quality and its influence on the cerium oxidation states. The received results were used to evaluate the synthesis method's suitability for suggested utilization. We used nanoparticles prepared by electron beam evaporation. This unique physical method includes nanoparticle creation through the fast cooling process followed by breaking radiation damaging nanoparticle surfaces to create surface off-stoichiometry. We prepared a sample containing clusters of a mixture of ultra-small nanoparticles and approximately 100 nm particles. X-ray diffraction confirmed the CeO2 phase in both components. To extract the finest component, we used centrifugal size fractionation. We received 200 nm clusters of 2-10 nm nanoparticles. Nanoparticle shapes and facet types were analyzed using transmission electron microscopy methods. We found out most nanoparticles were formed with truncated octahedrons containing {1,1,1} and {1,0,0} facet types and truncated cuboctahedrons containing {1,1,1}, {1,0,0}, and additional {1,1,0} facets. No octahedron (without truncation) containing only {1,1,1} facets was observed. Nanoparticle shapes containing {1,1,0} and {1,0,0} are suitable for redox activity. Some amount of irregular shapes, beneficial for redox activity, was also observed. Spectroscopy methods confirmed Ce3+ content.
Užití elektronové difrakce k mapování elastického napětí
Ondračka, Václav ; Kuběna, Ivo (oponent) ; Spousta, Jiří (vedoucí práce)
Metoda difrakce zpětně odražených elektronů je známou a běžně používanou metodou k určení orientace a velikosti zrn. Její použití pro mapování elastické deformace a ro- tace způsobené plastickými deformacemi tak rozšířené není. Tato diplomová práce se věnuje popisu standardního EBSD systému. Poznatků o použitých soustavách, notace orientace zrn a kalibrace systému je pak využito pro vytvoření svobodného softwaru pro mapování elastické deformace a rotace v rámci jediného zrna nebo monokrystalu, pracujícího s daty získanými z komerčních EBSD systémů.
LCF behaviour of 301LN steel: coarse-grained vs. UFG-bimodal structure
Man, Jiří ; Chlupová, Alice ; Kuběna, Ivo ; Kruml, Tomáš ; Man, O. ; Järvenpää, A. ; Karjalainen, L. P. ; Polák, Jaroslav
Low-cycle fatigue (LCF) behaviour of metastable austenitic 301LN steel with different grain sizes – coarse-grained (14 µm) and UFG (1.4 µm) with a grain bimodality – produced by reversion annealing (RA) was investigated. Symmetrical push-pull LCF tests were conducted on flat sheet specimens at room temperature with constant strain rate of 2×10–3 s–1 and constant total strain amplitude ranging from 0.4% to 0.8%. After completion of fatigue tests a ferritescope was adopted for quantitative assessment of volume fraction of deformation induced martensite (DIM). Microstructural changes, distribution and morphology of DIM in the volume of material were characterized at different scales by colour etching, TEM and EBSD techniques. Experimental data on microstructural changes are confronted with the stress-strain response and with the chemical heterogeneity present in the material.
W-B-C Nanostructured Layers - Microstructure and Mechanical Properties
Buršík, Jiří ; Kuběna, Ivo ; Buršíková, V. ; Souček, P. ; Zábranský, L. ; Mirzaei, S. ; Vašina, P.
Several W-B-C layers were prepared by magnetron sputtering. The microstructure of thin layers was observed by means of scanning and transmission electron microscopy on cross sections prepared using a focused ion beam. Both undisturbed layers and the volume under indentation prints were inspected.
MICROSTRUCTURE EVOLUTION DURING FATIGUE LOADING OF BULK NANOSTRUCTURED ALLOY AL(93)FE(3)CR(2)TI(2)
Chlupová, Alice ; Chlup, Zdeněk ; Kuběna, Ivo
The results of observation of the microstructure evolution during fatigue loading of the bulk nanostructured quasicrystalline Al alloy are presented. Feedstock powder with nominal composition of Al93Fe3Cr2Ti1 produced by gas atomization was hot extruded for powder compaction. The enhanced strengthening of the quasicrystalline nanostructured Al alloy is attributed to the microstructure refinement, formation of supersaturated solid solution, presence of reinforcing icosahedral quasicrystalline phase and work hardening caused by the deformation during extrusion. Good thermal stability is supported by presence of spherical quasicrystalline particles with different interior structure and sizes of up to 250 nm in the diameter. Low cycle fatigue stress-strain characteristics and microstructural evolution of the material were studied. For the microstructure observation the samples of material before and after fatigue loading the TEM and SEM microscopy was employed. The microstructure evolution caused by cyclic loading with positive mean stress was evaluated.
Nové kompozice pokročilých oxidicky zpevněných ocelí na bázi prvků vzácných zemin
Pech, Filip ; Kuběna, Ivo (oponent) ; Hadraba, Hynek (vedoucí práce)
Hlavním cílem této práce je příprava tří tříd ocelí lišících se obsahem chromu: 9Cr, 14Cr a 17Cr a jejich varianty zpevněné oxidickou disperzí. Oceli byly připraveny z atomárních a předlegovaných prášků metodou mechanického legování a zhutněny technikou spark plasma sintering. Jako zpevňující prvky bylo použito yttrium, které je v případě ODS ocelí nejobvyklejší a hliník. Tvorba oxidické disperze byla provedena dvěma způsoby: přímým přidáním oxidů Y2O3 a Al2O3 a vnitřní oxidací yttria a hliníku. Provedeným experimentem bylo zjištěno, že lze vytvořit ODS oceli oběma způsoby tvorby oxidické disperze. U ocelí zpevněných hliníkem však lze dosáhnout dostatečně jemné disperze oxidů pouze při použití vnitřní oxidace.
Early Stages of Fatigue Damage of Steels for Fusion Energetics
Kuběna, Ivo ; Spätig, Philippe (oponent) ; Lukáš, Petr (oponent) ; Kruml, Tomáš (vedoucí práce)
The main aim of the thesis is to explain fatigue behaviour of the ODS Eurofer steel, 14Cr ODS ferritic steel produced in the CEA (Commissariat a l’énergie atomique, Saclay, France) and 14Cr ODS ferritic steel produced in the EPFL (École Polytechnique Fédérale de Laussane, Switzerland). The results are compared with non–ODS variant of Eurofer steel, if possible. This work is part of a wide collaboration coordinated by the EFDA (European Fusion Development Agreement) on development of structural materials for future fusion reactors. The following experiments were carried out: • Standard fatigue experiments were performed at room temperature, at 650 and at 750 . Cyclic hardening/softening curves, cyclic deformation stress–strain curves, Coffin–Manson curves and Wöhler curves were measured. Detailed analysis of hysteresis loops was performed. • The microstructure of the as–received state was studied by TEM and compared with the microstructure after fatigue loading in order to reveal microstructural changes due to fatigue loading. • Surface roughening due to cyclic plastic localisation was observed. Crack initiation sites were detected and the mechanism of crack initiation was analysed. • Kinetics of small fatigue crack growth was measured. It was found that fine oxide dispersion strengthens studied materials significantly, reduces cyclic softening and stabilises the microstructure in the whole range of testing temperatures. The maximum application temperature is increased. Significant differences in fatigue life of the ODS steels were found and explained by differences in crack initiation mechanisms and small fatigue crack growth rate.
Testování lomové houževnatosti za vysokých teplot s využitím miniaturních CT těles
Holas, Jiří ; Kuběna, Ivo (oponent) ; Šiška, Filip (vedoucí práce)
Tato diplomová práce se zabývá hodnocením lomového chování ODS oceli MA956 za vysokých teplot. Toto chování bylo testováno pomocí miniaturních CT těles, na kterých byly provedeny zkoušky za účelem změření křivek odolnosti proti šíření tvárné trhliny (J-R křivky), ze kterých byla určena hodnota lomové houževnatosti. Lomové vlastnosti byly dále hodnoceny pomocí faktografické analýzy lomových ploch. Strukturní vlastnosti materiálu byly určeny pomocí měření tvrdosti a analyzovány metalografickými metodami. Výsledky měření ukazují pokles lomové houževnatosti s rostoucí teplotou.
Vývoj metodiky nanoobrábění při studiu mechanických vlastností tenkých vrstev pomocí fokusovaných iontových svazků
Kuběna, Ivo ; Švejcar, Jiří (oponent) ; Kruml, Tomáš (vedoucí práce)
Hlavním obsahem této diplomové práce je vytvoření metodiky přípravy mikrokompresních vzorků z tenké kovové vrstvy připravené metodou PVD. Testovaný materiál byl připraven firmou ON Semiconductor Rožnov pod Radhoštěm. Studovaná vrstva měla složení Al-1,5 hm% Cu a je používaná pro vodivé spoje na integrovaných obvodech. Na křemíkový substrát je nejprve napařena mezivrstva se složením W-10 hm% Ti pro lepší adhezi testované vrstvy. Geometrie vzorku by se měla co nejvíce blížit rotačnímu válci, jehož výška je dána tloušťkou vrstvy a jehož průměr je přibližně 1 m. Pro přípravu takového mikrokompresního vzorku bylo použito přístroje Quanta 3D FEG Dual BeamTM využívajícího technologii fokusovaného iontového svazku. Experimenty na tomto přístroji byly prováděny na půdě společnosti FEI Company v Brně. Bylo připraveno 39 mikrokompresních vzorků za různých podmínek iontového odprašování. Optimalizací parametrů procesu přípravy bylo dosaženo požadované geometrie, zlepšení rovnoběžnosti stěn a rovnoměrnosti dna v blízkém okolí vzorku a jeho plynulý přechod do základního substrátu. Připravené vzorky jsou vhodné pro mikrokompresní testy, které již byly úspěšně provedeny ve spolupráci s Fyzikálním ústavem AV ČR v Praze.
Determination of mechanical properties from microcompression test
Truhlář, Michal ; Kruml, Tomáš ; Kuběna, Ivo ; Petráčková, Klára ; Náhlík, Luboš
This paper describes a microcompression test of Al - 1.5 wt. % Cu thin film deposited on Si substrate. Microcompression combines the sample preparation with the use of ion focused beam (FIB) with a compression test carried out using nanoindenter. Cylindrical specimens (pillars) were prepared using FIB. The diameter of pillars was about 1.3 μm and their height was about 2 μm (equal to the film thickness). Stress-strain curves of the thin film were obtained. The results depend on crystallographic orientation of pillar. The paper is focused to an attempt to determine as precisely as possible Young modulus of the film using experimental data and finite element modelling.

Národní úložiště šedé literatury : Nalezeno 18 záznamů.   1 - 10další  přejít na záznam:
Chcete být upozorněni, pokud se objeví nové záznamy odpovídající tomuto dotazu?
Přihlásit se k odběru RSS.