|
|
MICROSTRUCTURAL INVESTIGATION AND MECHANICAL TESTING OF AN ULTRAFINE-GRAINED AUSTENITIC STAINLESS STEEL
Chlupová, Alice ; Man, Jiří ; Polák, Jaroslav ; Karjalainen, L. P.
Special thermomechanical treatment based on high degree deformation followed by reversion annealing was applied to 301LN austenitic stainless steel to achieve ultrafine-grained (UFG) structure with considerably enhanced mechanical properties. Two different conditions of the thermomechanical treatment were adopted and resulting microstructures with different grain sizes were characterised by optical and high resolution scanning electron microscopy (FEG SEM). Hardness measurements and tensile tests were performed to characterize mechanical properties. To reveal structural changes induced during thermomechanical treatment and during tensile tests a magnetic induction method was additionally applied. Experimental study validated the ability of the treatment to produce an austenitic stainless steel with the grain size of about 1.4 mu m which exhibits tensile strength of around 1000 MPa while ductility remains close to 60 %. The results obtained for both thermomechanical conditions are compared and the relationship between microstructure refinement, phase content and mechanical properties is discussed.
|
|
|
MICROSTRUCTURAL INVESTIGATION AND MECHANICAL TESTING OF AN ULTRAFINE-GRAINED AUSTENITIC STAINLESS STEEL
Chlupová, Alice ; Man, Jiří ; Polák, Jaroslav ; Karjalainen, L. P.
Special thermomechanical treatment based on high degree deformation followed by reversion annealing was applied to 301LN austenitic stainless steel to achieve ultrafine-grained (UFG) structure with considerably enhanced mechanical properties. Two different conditions of the thermomechanical treatment were adopted and resulting microstructures with different grain sizes were characterised by optical and high resolution scanning electron microscopy (FEG SEM). Hardness measurements and tensile tests were performed to characterize mechanical properties. To reveal structural changes induced during thermomechanical treatment and during tensile tests a magnetic induction method was additionally applied. Experimental study validated the ability of the treatment to produce an austenitic stainless steel with the grain size of about 1.4 mu m which exhibits tensile strength of around 1000 MPa while ductility remains close to 60 %. The results obtained for both thermomechanical conditions are compared and the relationship between microstructure refinement, phase content and mechanical properties is discussed.
|
|
|
LCF behaviour of 301LN steel: coarse-grained vs. UFG-bimodal structure
Man, Jiří ; Chlupová, Alice ; Kuběna, Ivo ; Kruml, Tomáš ; Man, O. ; Järvenpää, A. ; Karjalainen, L. P. ; Polák, Jaroslav
Low-cycle fatigue (LCF) behaviour of metastable austenitic 301LN steel with different grain sizes – coarse-grained (14 µm) and UFG (1.4 µm) with a grain bimodality – produced by reversion annealing (RA) was investigated. Symmetrical push-pull LCF tests were conducted on flat sheet specimens at room temperature with constant strain rate of 2×10–3 s–1 and constant total strain amplitude ranging from 0.4% to 0.8%. After completion of fatigue tests a ferritescope was adopted for quantitative assessment of volume fraction of deformation induced martensite (DIM). Microstructural changes, distribution and morphology of DIM in the volume of material were characterized at different scales by colour etching, TEM and EBSD techniques. Experimental data on microstructural changes are confronted with the stress-strain response and with the chemical heterogeneity present in the material.
|
|
|
Microstructural Investigation and Mechanical Testing of an Ultrafine-grained Austenitic Stainless Steel
Chlupová, Alice ; Man, Jiří ; Polák, Jaroslav ; Karjalainen, L. P.
Special thermomechanical treatment based on high degree deformation followed by reversion annealing was applied to 301LN austenitic stainless steel to achieve ultrafine-grained (UFG) structure with considerably enhanced mechanical properties. Two different conditions of the thermomechanical treatment were adopted and resulting microstructures with different grain sizes were characterised by optical and high resolution scanning electron microscopy (SEM-FEG). Hardness measurements and tensile tests were performed to characterize mechanical properties. To reveal structural changes induced during thermomechanical treatment and during tensile tests a magnetic induction method was additionally applied. Experimental study validated the ability of the above special treatment to produce austenitic stainless steel with grain size about 1.4 m which exhibits tensile strength about 1000MPa while ductility remains on level about 60 %. The results obtained for both thermomechanical conditions are compared and the relationship between microstructure refinement, phase content and mechanical properties is discussed.
|
host ::
RSS.