|
|
Proposal of a new type of steam turbine blade attachement
Vrbický, Jiří ; Petruška, Jindřich (referee) ; Polzer, Stanislav (advisor)
This thesis describes design of new circumferential blade attachment on last grade of steam turbine and following stress-strain analysis by FEM with static and cyclic loading. It was created two new design of geometry, which were created based on existing and operating constructional solution of oblique double T blade attachment. It was made stress-strain FEM analysis on original design of blades. Its results served to realize change of construction. Their target was increase load capacity and service life of new types of blade attachment.
|
|
|
Stress, deformation and safety analysis of the recumbent bicycle frontal composite axle
Ondrejka, Jan ; Majer, Zdeněk (referee) ; Vrbka, Jan (advisor)
This diploma thesis deals with creation of computational model of AZUB recumbent tricycle composite axle for stress strain analysis. The thesis consists of four main parts. The first part contains introduction to the offer of full suspended tricycles from the most known manufacturers. Furthermore it contains introduction to composite materials that makes the main element of AZUB´´s suspension, and the description of the AZUB´´s front axle. In the second part there is detailed compilation of computational model for purpose of stress strain analysis of three load states. The effect of specific material and geometry parameters on axle behavior is discussed with the aim of choosing the most appropriate variant. Third part deals with the manufacturing of the front axle prototype and with tests leading to input data for numerical model and verification of computational model. Modifications and changes that lead to manufacturing of the second prototype are content of the last part. Based on this experience some recommendations for future development of the numerical axle model and the front axle suspension itself are formulated.
|
|
|
Stress-strain Analysis of Diesel Particulate Filter Support on Tractor Zetor Forterra
Kučera, Petr ; Ramík, Pavel (referee) ; Dundálek, Radim (advisor)
The subject of this master's thesis is the FEM analysis of the construction of the diesel particulate filter support on the tractor Zetor Forterra. The introduction of this thesis is about the theoretical part dealing with the issue of emissions from diesel engines and ways to reduce them. The following part describing the creation of the computational model. Then, the static stress-strain analysis, modal analysis and fatigue analysis are solved in the ANSYS Workbench software. The assessment of the safety of the structure in terms of limit states, that may occur during the operation of the tractor, based on the results of calculations is in the conclusion of the thesis.
|
|
|
Creating a computational model for stress-strain analysis of parts of generator
Sedláček, Radek ; Fučík, Karel (referee) ; Návrat, Tomáš (advisor)
This thesis focuses on creating of a computational model for stress-strain analysis of parts of a generator. Computational model is parametric and it allows use of various geometric variants of the shaft and rotor lamination. Parametric computational model in APLD language is compiled in the attached sheet of software MS Excel after entering input values. After solving in software ANSYS 14.5 are results imported into MS Excel sheet for further post processing.
|
|
|
Determination of elastic modulus of thin layer - numerical study of microcompressive test and the bulge test
Petráčková, Klára ; Pokorný, Pavel (referee) ; Náhlík, Luboš (advisor)
Determination of mechanical properties of very thin films is rather difficult task as all of currently using testing techniques have some weakness. This master’s thesis deals with microcompressive test and bulge test. Finite element simulations of the two methods were carried out in order to better understanding of experimental record. Microcompression combines the sample preparation with the use of focused ion beam (FIB) with a compression test carried out using nanoindenter. Cylindrical specimens (pillars) were prepared from Al film deposited on Si substrate using FIB. Experimentally measured data on pillars needs correction to obtain undistorted material properties of Al thin film. A necessary correction using FE modeling is suggested in the thesis. Second part of the work is focused on modeling of bulge test. Pressure is applied on freestanding SiNx film while deflection of the film is measured. Stress state in the film is biaxial making determination of mechanical properties of the film more complicated. The goal is to present how to model the whole problem. In addition, preparation of the specimens was simulated to estimate residual stress in the film. The paper contributes to a better characterization of very thin surface layers and determination of their mechanical properties.
|
|
|
Biomechanical studies carpometacarpal (CMC) joint thumb
Podsedník, Karel ; Marcián, Petr (referee) ; Florian, Zdeněk (advisor)
This master thesis deals with stress-strain analysis of carpometacarpal (CMC) thumb joint. It is a preliminary study, which was not analysed on BUT Mechanical and biomechanical institute yet. There is a comparative stress-strain analysis of CMC with applied total endoprosthesis and physiological condition. The model of geometry was created based on CT images and processed with using software Catia and Solidworks. The problem was solved in numerical FEM (finite element method) in software Ansys 13.0
|
|
|
Biomechanical study of the upper limb wrist
Kouřil, Jan ; Marcián, Petr (referee) ; Florian, Zdeněk (advisor)
This master´s thesis is focused on biomechanical study of wrist. There is a literature search on this theme in the beginning of this work. The thesis is described in detail anatomy of bones in the wrist. Subsequent the stress-strain analysis of physiological wrist is implemented in a neutral position. The model of geometry of wrist is created on base of CT data. To create calculation model and the solution is implemented in the computer system ANSYS Workbench.
|
|
|
Analysing of the design of the opening mechanism for the floor hatch
Metelka, Jiří ; Houfek, Martin (referee) ; Fuis, Vladimír (advisor)
In a family house not far from Brno, there is an entryway hole for getting into the space under the floor. The hole is covered by a high weight concrete hatch. For easier manipulation with the hatch an opening mechanism was designed and manufactured. This mechanism had been installed under the hatch and nowadays it works well. This master’s thesis deals with description of main components of the mechanism and their function. Load analysis and stress-strain analysis are the major part of this thesis. At the end of this work the analysis results are commented and some suggestions for further research are proposed.
|
|
| |
|
|
Stress-strain analysis of aortic aneurysms
Man, Vojtěch ; Janíček, Přemysl (referee) ; Burša, Jiří (advisor)
This master thesis is focused on stress-strain analysis abdominal aortic aneurysm using ANSYS software. The model of abdominal aortic aneurysm are based on CT scans of five specific patients. The branching arteries are included to the model and one goal of this thesis is decision about their influence of the wall stress. In this thesis was used a hyperelastic materiál model, which is based on mechanical tests done on human arterial samples.
|
guest ::
