|
|
Electrical machine for wind power generator
Srna, Jan ; Chmelíček, Petr (referee) ; Kurfűrst, Jiří (advisor)
This thesis describes analyse of transient and subtransient parts of short – circuit current. Values of synchronous generator short – circuit current were measured for lower voltage and subsequently recounted to its nominal values. The analyse is useful for machines without documentation and where is measurement of needed parameters necessary. Two methods coming out of the IEEE standard were used for identification reactances and time constants and after that these methods were compared between themselves. One of the method were created in program MATLAB, where measured short – circuit currents for each phase were handled. Values of time constants are used for simple model of synchronous generator created in toolbox of program MATLAB/SIMPOWER. This simulation verifies correctness of counting transient and subtransient analyses.
|
|
| |
|
|
Magnetic field calculating of transformer by using conducting model
Bláha, Martin ; Skalka, Miroslav (referee) ; Kurfűrst, Jiří (advisor)
The paper deals with conductivE-resistive network. Use of this network is modeled transformer. The model is implemented in simulation program PSPICE and Simscape. To evaluace the results were used the values obtained using the finite element method. A simple model of the transformer has been replaced by rezistor network conductivity, which is divided into elements. According to these elements is a simplified model designed and analyzed
|
|
|
Faults identification of AC windings in production process
Samek, Josef ; Kurfűrst, Jiří (referee) ; Ondrůšek, Čestmír (advisor)
In this paper stator manufacturing process of stator is described. Mainly description is aimed on winding, insulation and copper wire. Discussion about origin of insulation damage possibilities during manufacturing is included. Statistics survey about failure causes of stator revealed during manufacturing process and warranty claims is presented. One test method from list of market available winding tests is chosen - partial discharge; described in detail and applied on the correct stator and the damaged stator. Results are interpreted.
|
|
|
Electrical machine for wind power generator
Srna, Jan ; Chmelíček, Petr (referee) ; Kurfűrst, Jiří (advisor)
This thesis describes analyse of transient and subtransient parts of short – circuit current. Values of synchronous generator short – circuit current were measured for lower voltage and subsequently recounted to its nominal values. The analyse is useful for machines without documentation and where is measurement of needed parameters necessary. Two methods coming out of the IEEE standard were used for identification reactances and time constants and after that these methods were compared between themselves. One of the method were created in program MATLAB, where measured short – circuit currents for each phase were handled. Values of time constants are used for simple model of synchronous generator created in toolbox of program MATLAB/SIMPOWER. This simulation verifies correctness of counting transient and subtransient analyses.
|
|
|
Magnetic field calculating of transformer by using conducting model
Bláha, Martin ; Skalka, Miroslav (referee) ; Kurfűrst, Jiří (advisor)
The paper deals with conductivE-resistive network. Use of this network is modeled transformer. The model is implemented in simulation program PSPICE and Simscape. To evaluace the results were used the values obtained using the finite element method. A simple model of the transformer has been replaced by rezistor network conductivity, which is divided into elements. According to these elements is a simplified model designed and analyzed
|
|
|
Electromagnetic field calculation of Induction machine for different mechanical load
Hetflajš, Martin ; Kurfűrst, Jiří (referee) ; Skalka, Miroslav (advisor)
This bachelor’s thesis deals with an analysis of the induction machine electromagnetic field distribution with real parameters. Whole analysis was done for three point of the mechanical load by finite element method in ANSYS. In the next part is described a basic theoretically research of the electromagnetic field and also preliminary survey of the numeric method for FEM. This thesis also contains an analysis of electromagnetic model of analyzed induction machine with detailed description of each analysis step and in conclusion the results summary was done.
|
|
|
Calculation of induction machine stray looses
Jirásek, Tomáš ; Kurfűrst, Jiří (referee) ; Ondrůšek, Čestmír (advisor)
The main goal of this thesis is a determination of an idle additional losses in an electric rotary machines and a calculation of these losses for induction machine. The additional losses are caused especially by the eddy currents on the surface of stator and rotor, further by a pulsation of these currents owing to the periodical change of air-gap permeance, magnetic induction in stator and rotor teeth and a differential leakage.
|
|
|
Optimization of the permanent magnet machine based on the artificial inteligence
Kurfűrst, Jiří ; Duroň,, Jiří (referee) ; Singule, Vladislav (referee) ; Ondrůšek, Čestmír (advisor)
The dissertation thesis deal with the design and the optimization of the permanent magnet synchronous machine (SMPM) based on the artificial intelligence. The main target is to apply potential optimization methods on the design procedure of the machine and evaluate the effectiveness of optimization and the optimization usefulness. In general, the optimization of the material properties (NdFeB or SmCo), the efficiency maximization with given nominal input parameters, the cogging torque elimination are proposed. Moreover, the magnet shape optimization, shape of the air gap and the shape of slots were also performed. The well known Genetic algorithm and Self-Organizing migrating algorithm produced in Czech were presented and applied on the particular optimization issues. The basic principles (iterations) and definitions (penalty function and cost function) of proposed algorithms are demonstrated on the examples. The results of the vibration generator optimization (VG) with given power 7mW (0.1g acceleration) and the results of the SMPM 1,1kW (6 krpm) optimization are practically evaluated in the collaboration with industry. Proposed methods are useful for the optimization of PM machines and they are further theoretically applied on the low speed machine (10 krpm) optimization and high speed machine (120 krpm) optimization.
|
|
| |
guest ::
RSS feed.