|
|
Multimedia quality assessment for headset with virtual reality
Majnuš, Robert ; Polák, Ladislav (referee) ; Kufa, Jan (advisor)
This bachelor thesis deals with creating multimedia content for virtual reality and designing a subjective test to evaluate these sequences. In the introductory theoretical part there is information about virtual and augmented reality and several types of virtual reality glasses that are available on the market today. The second chapter focuses on methods of quality measurement and evaluation. These are subjective and objective evaluation metrics. The following describes the different types of codecs that are found in most of the sequences on the Internet portals. Then there is a chapter on creating content for virtual reality. Especially panoramic, 3D and 360 ° videos and photos. In the practical part of this semester work is described by me the procedure of editing sequences for individual codecs and design and use of subjective method including evaluation.
|
|
|
Compact Bluetooth multimetr
Kolář, Ondřej ; Kufa, Jan (referee) ; Rozum, Stanislav (advisor)
The first part of bachelor's thesis Compact Bluetooth multimeter discusses Bluetooth Low Energy technology. It describes individual layers and protocols of its communication chain. There are also described some of the electronic ciruits and methods used for measuring in electronics. The second part of the bachelor's thesis describes practical design and implementation procedures of the compact multimeter which communicates with a smartphone application via Bluetooth Low Energy.
|
|
|
Strategy for Improvement of Training System of Company
Gazurová, Anna ; Kufa, Jan (referee) ; Mallya, Thaddeus (advisor)
This thesis focuses on problems related with new graduates at the „Department of New Employees Training“ of TŘINECKÉ ŽELEZÁRNY joint stock Company. The work evaluates to what extent the participants are satisfied with the training period, work of each mentor assigned to them and how they are involved in solving concreate tasks. Later suggestions are made on what measures should be taken to improve the program, for future participants to be satisfied.
|
|
|
Measurement and analysis of the DAB system
Kaštánek, Petr ; Kufa, Jan (referee) ; Polák, Ladislav (advisor)
This thesis deals with the measurement and analysis the performance of the Digital Audio Broadcasting (DAB) system. Theoretical part of the work contains a brief description of the signal processing chain of DAB. Attention is devoted to physical layer (PHY). In the experimental part of the work is designed and implemented laboratory measuring workplace for reception, processing and evaluation of DAB signal. The RTL2832U software defined radio (SDR) is used as a receiver of the DAB signal. The functionality of the proposed concept is verified by a detailed measurement.
|
|
|
Laboratory workplace for measuring performances of DVB-T2/T2-Lite
Krejčíř, Dominik ; Kufa, Jan (referee) ; Polák, Ladislav (advisor)
This thesis deals with proposal and realization an appropriate measurement workplace to measure performances of DVB-T2 and DVB-T2-Lite. Both systems for terrestrial digital video broadcasting are described. It is possible to measure objective parameters and evaluate the quality of DVB-T2/T2-Lite signal subjectively. The proposed concept was verified by a set of experimental measurements, which is divided into four scenarios. The measurement focuses to parameters of Set-Top-Boxes. The measurement allows to test and compare Set-Top-Boxes.
|
|
|
Automated measuring system for irrigating plants with IoT connectivity
Lahoda, Vladimír ; Polák, Ladislav (referee) ; Kufa, Jan (advisor)
This bachelor thesis deals with IoT networks and considers their use as part of embedded devices. The purpose of this device is to control the flower bed or garden based by data from sensors monitoring the environment. The device not only controls the irrigation operation itself, but also sends all traffic data over the IoT LoRa network. Thus, the device also functions as a weather station, as all data are sent to a second device that acts as a receiver. This receiver displays the data and also sends them to the Internet, where the data are publicly available. The module for sending and measuring data is mounted on its own PCB and is covered in a waterproof cover, so they can be operated outdoors. There is an integrated battery, which is a backup of savings in case of power failure. The battery is designed to back up power for 25 days.
|
|
|
Solar charger with balancing circuit for 4 cell battery pack working in an IoT network
Šlígl, Jan ; Kufa, Jan (referee) ; Herceg, Erik (advisor)
This bachelor thesis deals with the design of a circuit for charging control of the four battery cells using solar energy. Passive balancing is applied to the separate cells. The measured cell voltage should then be sent via the LoRa network. The proposal mainly considers low energy consumption, compactness and independence. The appropriate function is then verified using MATLAB Simulink simulations and subsequently tested on the STM32 development kit. The result will be a finished printed circuit board design and simulation of important parts of the device.
|
|
|
Comparison of objective and subjective video quality metrics for Ultra HDTV sequences
Bršel, Boris ; Krasula, Lukáš (referee) ; Kufa, Jan (advisor)
Master's thesis deals with the assessment of quality of Ultra HDTV video sequences applying objective metrics. Thesis theoretically describes coding of selected codecs H.265/HEVC and VP9, objective video quality metrics and also subjective methods for assessment of the video sequences quality. Next chapter deals with the implementation of the H.265/HEVC and the VP9 codecs at selected video sequences in the raw format from which arises the test sequences database. Quality of these videos is measured afterwards by objective metrics and selected subjective method. These results are compared for the purpose of finding the most consistent correlations among objective metrics and subjective assessment.
|
|
|
Shortwave power amplifier
Kufa, Jan ; Vařacha, František (referee) ; Prokeš, Aleš (advisor)
The aim of the master´s thesis is to create a high-frequency amplifier with switching power amplifier classes among classes A, B, C with output power of 10 W. The amplifier operates at frequency from 3.5 MHz to 14 MHz. Master´s thesis includes also theoretical analysis, design of lowpass filter and amplifiers and their simulation, mechanical realization and measured parameters of the amplifier.
|
|
|
Multifunction speaker with wireless connectivity
Baránek, Michal ; Kratochvíl, Tomáš (referee) ; Kufa, Jan (advisor)
Tato práce se věnuje multifunkčnímu systému s více možnostmi pro přenos zvukového signálu do reproduktoru. Problémem u dnes velmi populárních komerčních přenosných reproduktorů je absence autonomního zdroje hudby, například v podobě rádia. Proto je cílem této práce právě dosáhnout takového multifunkčního reproduktoru podobnému jako jsou komerční přenosné reproduktory, ale s možností přehrávání radia distribuovaného pomocí internetové sítě. Další z nejdůležitějších funkcí těchto reproduktorů je bezdrátové připojení, jako je Bluetooth, pro streamování zvuku, například z telefonu do reproduktoru. Další významné aspekty těchto reproduktorů jsou jednoduché uživatelské rozhraní, převážně ve formě ovládacích tlačítek, kvalitní zvukový výstup s přiměřeným výstupním výkonem k velikosti reproduktoru a velkou výdrží baterie pro několika hodinový poslech na nízké nebo střední úrovni hlasitosti. Proto jsou i tyto všechny funkce implementovány v této práci výroby multifunkčního reproduktoru.
|
guest ::
