|
|
Analytical Methods in Motorsport
Růžička, Bronislav ; Dočkal, Aleš (referee) ; Čejka, Václav (referee) ; Karpíšek, Zdeněk (referee) ; Mazůrek, Ivan (advisor)
This dissertation is focused on proposal for simplified data analyze approach for sport-car vehicle dynamic evaluation with relationship to possibility for qualified estimation of set-up parameters influence for overall vehicle performance. In common practice can be usual overlapping effect caused by concurrent changes of car setup elements if performed in the same moment with resulting in not correct or hardly definable process determination for evaluation and decision about next steps in car development. For analyze of these multidimensional data is then chosen process with approach by Linear Regression Model (LRM). In dissertation is proposed basic philosophy with concern on specificity of car vehicle dynamics, performed experiment with defined inputs including analyze and interpretation method of obtained outputs. This methodic take into account also possibility for general application of multidimensional data analyses not only in motorsport, but as well for dynamic behavior diagnostics of technical systems where finding of optimal running condition depends on multi-parametric setup whose combination must reflect often changes of outer conditions too.
|
|
|
The study of magnetorheological shaft seal
Pavlíček, Dušan ; Dočkal, Aleš (referee) ; Kubík, Michal (advisor)
This thesis deals with the experimental study of magnetorheological shaft seal. The purpose of this diploma thesis is to describe the operating parameters of rotational magnetoreological shaft seal. In thesis, the effects of magnetic field and shaft speed on the pressure resistance and braking torque are described. Operating parameters were measured by an experimental device. Research has shown that the magnetoreological seal is characterized by a high pressure resistant. Disadvantages are the high braking torque and leakage of carrier oil from the magnetorheological fluid. These problems have been solved by a new design of magnetic circuit, that has been identified as a magnetoreological gradient pinch seal (MRGPS).
|
|
|
Reconstruction of Gearbox Testing Rig
Rozsypálek, Tomáš ; Dočkal, Aleš (referee) ; Klapka, Milan (advisor)
The aim of this diploma thesis is reconstruction of gearbox testing rig. Modernization will allow fully automatic long-term gearbox tests according to pre-defined test parameters. The first part of thesis describes commercial and scientific solutions of used testing rigs. Individual solutions are inspected and evaluated for applicability to upgrade the testing rig. The second part of diploma thesis deals with selection of purchased components for allowing automatic drive, design concepts, selection of appropriate design, assembly and installation of control board and calibration of used components. This part of diploma thesis deals with analysing of software solution made for automatic drive too. The output of this work is a functional sample of control hardware and software for automatic and manual control which contains recording of measured data.
|
|
|
Construction of comparison measuregauge for measurement of tools.
Brabenec, Petr ; Dočkal, Aleš (referee) ; Ždímal, Pavel (advisor)
This work is about construction of a comparison gauge to meausure revolving tools. The gauge measures cutting and clamping parts of standard and special reamers. The gauge is unique and is designed for a company manufacturing concerete. It was designed in accordance with requirements and a prototype was tested for functionality. There is made analysis, development, design, theoretic estimation and practical verification of accurancy.
|
|
|
Modernization of R-mat test stations
Papaj, Lukáš ; Dočkal, Aleš (referee) ; Mazal, Pavel (advisor)
The aim of the thesis is to reconstruct obsolete R-mat test stations, which are used for rolling contact fatigue tests of material, which are still of interest from industry. It was necessary to replace the original control electronics with a new industrial computer to allow use modern sensors and automate the entire test process. At the same time, the measurement was supplemented by an acoustic emission method, which can also record the development of damage. Design modifications have been made that allow the installation of all new sensors. The main method for evaluating the tests is vibrodiagnostics, which is supplemented by the acoustic emission method. With the help of several experiments, the shortcomings of the new control system were identified, some parameters were designed, and the main functionality of the modernized R-mat station was verified. According to the proposed parameters and the identified shortcomings, the control system was modified, and a script was created, which is used to evaluate the test. It is still possible to perform rolling contact fatigue tests of the material on the modernized equipment, and thanks to the modernization of the electronics, it is possible to test completely new methods of test evaluation.
|
|
|
Design automation of simple inject moulds for tool factory
Žváček, Michal ; Dočkal, Aleš (referee) ; Paloušek, David (advisor)
The dissertation is concerned with automatization proposal of simple injection moulds for plastics. The dissertation is concentrating on the process of CAD design with the aim of make it more effective and automate by the help of 3D parametric strickle board of moulds. It serves for rapid proposal of basic mechanism of the tools. Strickle board of the mould is managed by length of side moulding plate in required range from 300 to the 700mm. For managing of standardized parts was created web portal, which includes database of single parts. These parts can be simply insert to the groups of moulds by the help of hypertext links in software Catia V5. Dissertation includes description of whole system automatization and matching of the new way of CAD design with the original.
|
|
|
Experimental chamber for testing of special materials using SLM technology
Malý, Martin ; Dočkal, Aleš (referee) ; Koutný, Daniel (advisor)
The thesis deals with the influence of process temperature and pressure on 3D printing using Selective Laser Melting. The aim of the thesis is the design, manufacture and testing of the experimental chamber for SLM 280HL from company SLM Solutions. The main task of the experimental chamber is to increase the temperature of the preheating of the powder bed from the original 200 °C to at least at 400 °C. The device will be used to investigate the influence of high process temperature on the properties of printed materials. The thesis also deals with the design of the powder applicator for elevated temperatures.
|
|
|
Experimental Analysis of Kinematic Quantities on Cam Mechanism
Komenda, Lukáš ; Dočkal, Aleš (referee) ; Zimmerman, Martin (advisor)
This diploma thesis deals with creation of a laboratory task related with analysis of kinematic quantities on cam machanism. A new measuring chain was created as a part of the new laboratory task for analysis of kinematic quantities with use of sensors and signal processing by software LabVIEW. The concept of the laboratory task on a experimental machine was based on knowledge gained from Current State of Knowledge where basic principles of laboratory training and utilization of cam mechanisms in learning were described.
|
|
|
Design of magnetorheological clutch.
Nováček, Vladislav ; Dočkal, Aleš (referee) ; Roupec, Jakub (advisor)
This thesis deals with the design of the magnetorheological (MR) clutch. The extensive literature research with particular conclusions to each design variant of MR clutches or brakes has been done in the first part of the thesis. The second part of the thesis describes the design of the actual MR clutch based on the results of the analytical calculation of the magnetic circuit. Finally, the experiments verifying the function of the key segments of the clutch, and the whole clutch are summarized in the third part of the thesis.
|
|
|
Analysis of drive corned filler including feed worm and conveyer
Mahút, Tomáš ; Dočkal, Aleš (referee) ; Dvořáček, Jiří (advisor)
This final project solves a proposal of mechanism for splitting of unfilled cans before a can filling process in the food industry. From all possible options such as the one with a simple conception, easy applicated in practice and at a low price, should be chosen. The selected option is constructed and drawn in a 3D programme called AUTODESK Inventor 10. Please, see the attached technical drawings for the chosen parts.
|
guest ::
