|
|
Wind power plant
Šponiarová, Petra ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
The electricity production from renewable sources is a very current topic. It also includes the electricity made by wind power plants, which the bachelor’s thesis concentrates on. An extensive research study was conducted to provide an overview of wind turbine types. Concerning wind power plants, apart from their visual impact, noise and vibration connected to their operating is an often discussed issue. The construction of a wind turbine stands for the most important role in reducing such unwanted effects. Technical experiments following specific standards and recommendations are performed to assess the impact of wind turbines-emitted noise and vibration on humans. In order to assess noise and vibration of a wind turbine a technical experiment is proposed, which uses different approaches to determine the critical components. The selection of a suitable measuring equipment and the choice of location for its subsequent use are important parts of the design. At last, the use of wind power plants is critically reviewed.
|
|
| |
|
|
Noise Analysis of Basic Circuits for Analog Signal Processing
Humpolíková, Michaela ; Sládok, Ondřej (referee) ; Kubánek, David (advisor)
The cause of noise in analog circuits is a problem of quality in output signals. There are many reasons of its occurrence, noise is caused by components connected into the circuit, and the assembly itself. This bachelor thesis summarizes the theoretical knowledge about noise analysis. Noise measurement in circuits can now be calculated with PSpice, the results are used for the design of low noise circuits. In the contained practical analysis of the circuits were achieved the results for the suitable designing of low noise circuits.
|
|
|
Usage of transmission at electric vehicles
Běloušek, Ondřej ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
At first bachelor thesis divides different conceptions of electric vehicles with the aim to describe characteristic components which electric vehicles contain, and that make it different in comparison with conventional cars. From the principle of the electric vehicle it is obvious that electric energy which is necessary for electric drive must be stored and for this reason the batteries and important components are described. The next part is dedicated to the powertrain which is affected by the presence or absence of an internal combustion engine and its usage rate. Common feature is an electric machine which transforms electrical energy into mechanical energy, and which makes powertrain complete. Gearboxes used at electric vehicles are the next part which is affected by the type of power unit that they cooperate with. For that reason, one representative from each part is described. The representative of hybrid electric vehicles is planetary gear set of Toyota Prius 2010, representative of battery electric vehicles is one-speed transmission of Tesla cars and in the end the multi-speed transmission is mentioned because it is today´s trend. Because of the absence of an internal combustion engine for some types of electric vehicles, the noise and vibrations from gearbox come to the fore. The main source of the vibration is gears teeth contact and rattle of the other components. The last part of the thesis is focused on the design of a technical experiment that is suitable for measuring vibration and noise from two-speed automatic transmission. Firstly, the theoretical basis of measurement is described. The design itself takes into account the suitable measuring equipment, the right choice of components that realize closed loop and installation space of the acoustic chamber.
|
|
|
Noise Reduction Methods in Automotive Design
Kubica, Petr ; Janoušek, Michal (referee) ; Prokop, Aleš (advisor)
The aim of this bachelor thesis is create a research study about noise reduction methods in automotive design. The introduction of this work deals with acoustic and the influence of noise on people. Furthermore it deals with ways of noise creation in a car and its suppression. In the end of this work there is a valorization of certain methods at noise suppression of a personal vehicle.
|
|
|
NVH parameters determination of gearbox housing
Belák, Kristián ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
This master’s thesis deals with determination of NVH parameters of the gearbox housing. Introductory part is focused on the necessary theoretical knowledge. Subsequently, it contains the modal analysis with the computational and experimental approach, which are being compared to each other. In the case of the computational approach, analysis of the influence of bolt pretension on the modal properties is also involved. The thesis continues with the harmonic analysis with the computational and experimental approach, including their mutual comparison. Based on these analyses, design modifications for improvement of the NVH parameters are designed at the end of the thesis, which are being compared to each other and to the original geometry, using the computational approach.
|
|
|
Neural Network Based Edge Detection
Janda, Miloš ; Žák, Pavel (referee) ; Švub, Miroslav (advisor)
Aim of this thesis is description of neural network based edge detection methods that are substitute for classic methods of detection using edge operators. First chapters generally discussed the issues of image processing, edge detection and neural networks. The objective of the main part is to show process of generating synthetic images, extracting training datasets and discussing variants of suitable topologies of neural networks for purpose of edge detection. The last part of the thesis is dedicated to evaluating and measuring accuracy values of neural network.
|
|
|
NVH parameter determinantion of plate
Bouchner, Michal ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
The aim of this thesis is examination and verification of numeric model for solving acoustics and vibration problems. Specifically, we are speaking about cast iron plate machined from gearbox. Main objectives of this work is set of experimental and numerical analysis at this simplified part with follow-up numerical model, where same analyses examining not only structure, but especially acoustic space around were performed. Due to this we were able to compare data between experimental and numerical analyses and to be able to prove or disprove functionality and limitation of numerical model.
|
|
|
Design of modern speaker body with usage of new technology
Kůst, Martin ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
This diploma thesis deals with the analysis and design optimization of a speaker cabinet (enclosure) produced by the additive technology of 3D sand printing. The introductory part is devoted to the theory, both in the field of noise, vibration and the method of their calculations, as well as the theory of speakers and their systems. Numerical and experimental modal analysis is performed, which were compared to determine the mechanical properties of the new material, including material damping. This is followed by experimental and numerical harmonic analysis, with output in the form of a numerical model describing the behaviour of the structure during its excitation. The data are compared with a modal analysis of the internal acoustic space and the critical shapes and their frequencies are determined. At the end of the work, construction modifications are proposed to increase the rigidity of enclosures, the influence of which is evaluated on the created numerical models.
|
|
|
Utilization of light polarization when filtering the optical signal
Alexa, Jan ; Vlček, Čestmír (referee) ; Wilfert, Otakar (advisor)
This master thesis deals with the possibility of separation of useful signal from noise using polarization of laser radiation. This thesis is structured into 5 thematic units. The first unit is focused on laser radiation and its properties. The second part contains a deeper focus on the polarization of radiation, its description and the possibilities of measuring the polarization states. The third part of the thesis is devoted to the design of the measuring chains and identification of used elements. Chapter four contains measurement of status of the polarization and its results. The last chapter analyzes particular measuring chains outputs according to their spectral characteristics.
|
guest ::
