Národní úložiště šedé literatury Nalezeno 20 záznamů.  1 - 10další  přejít na záznam: Hledání trvalo 0.00 vteřin. 
Experimental evaluation of aluminothermic welds
Zeman, L. ; Valach, J. ; Zlámal, P. ; Krčmářová, N. ; Koudelková, Veronika ; Zeman, J.
The article presents a study of the mechanical processes occurring during the aluminother-mic reaction using experimental methods (strain gauges, digital image correlation, thermography,scanning electron microscopy, profilometry). The aluminothermic reaction is a highly efficient weldingmethod due to its exothermic behaviour, however, it places considerable demands not only on thewelding technique, but also on the capabilities of the experimental methods used - these limitationsare also discussed in the article. The aluminothermic reaction is associated with the formation of alocalised heat source with a time evolution dictated by the technological procedure, which manifestsitself in heat propagation to the surrounding weld material. The unequal evolution of the temperaturefield is the fundamental cause of the appearance of the heat affected zone or local deformations orsurface curvature, which was the focus of the experimental methods deployed above and the results ofwhich are shown in the article.
Sonda pro zjištění stavu povrchu u hlavní malých průměrů
Procházka, Adam ; Goldmann, Tomáš (oponent) ; Malaník, Petr (vedoucí práce)
Tato práce se zabývá analýzou způsobů pro měření profilu povrchů, návrhem a implementací zařízení určeného k jejich měření. Implementované zařízení využívá techniky nekontaktní triangulační profilometrie pro zjištění stavu vnitřního povrchu v hlavni pomocí promítání laserové linie na povrch hlavně a snímání promítnutého tvaru pod nenulovým pozorovacím úhlem. Zároveň sbírá informace o obrazové textuře vnitřního povrchu za použití LED osvětlení a data o poloze pořízených snímků za použití senzoru měřícího vzdálenost od konce hlavně. Součástí práce je také návrh a implementace ovládacích modulů vytvořených na míru pro použité LED a laserovou diodu. Výstup ze zařízení je prezentován v uživatelské aplikaci. Zařízení je navrženo pro fungování v trubicích s průměrem od 40 milimetrů.
Fabrication of conducting patterns by material electroless plating of printed precursor
Kováčová, Silvia ; Gemeiner,, Pavol (oponent) ; Dzik, Petr (vedoucí práce)
The subject of this diploma thesis is the preparation of conductive structures by electroless plating of an extruded precursor. The experimental part deals with the preparation of standard patterns based on the length of immersion time in a coppering bath. The precursor layers were applied with Fujifilm Dimatix to various receiver substrates. The individual substrates with the precursor layer were immersed in the copper solution within different time intervals. The structure of the layers of grown copper and their thickness was characterized by a profilometer.
Study of optical properties of thin films of perovskiteFAPbBr3 precursors
Smolková, Denisa ; Čech, Vladimír (oponent) ; Zmeškal, Oldřich (vedoucí práce)
This thesis examines the preparation of thin layers of material for photovoltaic applications with focused on perovskites and determining their optical properties. Basic information about the photovoltaic panels, especially about the perovskites, and the preparation of thin layers is supplied in the theoretical section. This section includes description of optical properties and the main method of study of optical properties, spectroscopic ellipsometry. Experimental section is focused on the preparation of thin layers of perovskites FAPbBr3 and its precursors by spin-coating. Optical properties are evaluated using profilometry, UV VIS spectrometry and spectroscopic ellipsometry. The conclusion summarizes the results of this experiment with focused on comparison of ellipsometric spectrums of perovskites and its precursors.
Pokročilé materiály pro organickou bioelektroniku
Sedlák, Jiří ; Salyk, Ota (oponent) ; Weiter, Martin (vedoucí práce)
Tato bakalářská práce se zabývá zkoumáním materiálu PEDOT:DBSA pro možné využití v organické bioelektronice. Nejprve byl standardizován postup pro přípravu vrstev látky PEDOT:DBSA o požadované tloušťce a byla sledována závislost tloušťky na vodivost materiálu. Následně byl testován vliv teplotní stabilizace a látek EG, DMSO a H2SO4 na vodivost připravených vrstev. Pro zvýšení vodivosti byly testovány dva principy. Prvním byl princip přídavku látek jako dopantů do kapalných roztoků polymeru. Druhým způsobem přípravy vzorků byla metoda sekundárního ošetření již připravených vrstev čistého PEDOT:DBSA. Všechny připravené polymerní vrstvy byly charakterizovány pomocí čtyřbodové analýzy a profilometrie.
Roughness Measurement With Laser Profilometry
Mach, Radoslav
The project deals with technology of laser profilometry for material roughness measurements purposes. The focus of this work is measuring roughness parameters of materials, such as metal with using of different types of laser emmited light. Results demonstrate correlation between the wavelengths of the used laser lights with measurement accurancy.
Study of the optical properties of graphene oxide thin films
Smolková, Denisa ; Zmeškal, Oldřich (oponent) ; Schmiedová, Veronika (vedoucí práce)
This thesis examines the preparation of thin layers and determining their optical properties. It is focused on graphene oxide. In the theoretical part, basic information about the thin layers and their preparation is supplied. That is followed by a description of various methods of determining their optical properties and properties of light. Experimental part and results are focused on the preparation of thin layers by spin-coating and evaluation of measured values using optical microscopy, profilometry, spectroscopic ellipsometry and UV VIS spectroscopy. The conclusion summarizes the results of these methods.
Study of the optical properties of titanium dioxide thin films
Rackovská, Anna Patrícia ; Schmiedová, Veronika (oponent) ; Zmeškal, Oldřich (vedoucí práce)
The bachelor thesis is focused on the acquirement of thin film layers optical properties characterisation methods, done on inject printed titanium dioxide layers deposed on soda lime glass. Its main emphasis was on spectroscopic ellipsometry that was used to determine the refractive indices and the extinction coefficients of the samples in range of wavelengths from 200 nm to 850 nm and layer thickness. This thesis also shows another options of thin film layers preparation and several other methods to characterise properties of samples, specifically optical microscopy, used to set sample boundary as rough, mechanical profilometry which defined thickness of layers in range of 80 nm for the most thin sample to 250 nm for the most thick sample, and UV-VIS spectroscopy.
Roughness measurement with laser profilometry
Mach, Radoslav ; Frk, Martin (oponent) ; Hejátková, Edita (vedoucí práce)
The bachelor thesis deals with technology of laser profilometry for material roughness measurements purposes. The theoretical part deals with all aspects of the issue in an effective way and highlights the essential characteristics of used components and material roughness. The focus of this work is in first step to describe the external factors affecting the visual image processing such as increasing of environment temperature and its effect for a camera sensors. And particularly the relationship between CMOS and CCD technologies. The second step is for measuring roughness parameters of materials, such as metal, wood, rubber and plastic with three different lasers. Results demonstrate correlation between the wavelengths of the used laser lights with particular materials.
Hloubkové profilování metodou spektrometrie laserem buzeného mikroplazmatu
Průcha, Lukáš ; Novotný,, Karel (oponent) ; Pořízka, Pavel (vedoucí práce)
Diplomová práce se zabývá použitím spektroskopie laserem buzeného mikroplazmatu (LIBS) pro hloubkové profilování a 3D mapování pozinkované oceli, používané v automobilovém průmyslu. Před vytvořením výsledných hloubkových map a hloubkových profilů byla provedena důkladná optimalizace experimentu. V této práci bylo ukázáno, že metoda LIBS se hodí na vytvoření hloubkových profilů, tak i hloubkových map. Teoretická část práce se zabývá popisem instrumentace metody LIBS, vlastností laserem buzeného mikroplazmatu a rešerší vědeckých prací, které se v minulosti zabývaly hloubkovým profilováním nebo mapováním metodou LIBS. Experimentální část popisuje provedenou optimalizaci experimentu. Optimalizovalo se časové zpoždění, hloubka a průměr kráterů pomocí profilometru, poloha ohniskové roviny vzhledem k povrchu vzorku a výběr čáry s co nejmenším zbytkovým signálem a malým rozptylem dat. Dále byly vytvořené hloubkové profily zinku, železa, manganu a chromu, hloubková mapa zinku a železa, a také spočtené hloubkové rozlišení pro oba prvky.

Národní úložiště šedé literatury : Nalezeno 20 záznamů.   1 - 10další  přejít na záznam:
Chcete být upozorněni, pokud se objeví nové záznamy odpovídající tomuto dotazu?
Přihlásit se k odběru RSS.