Národní úložiště šedé literatury Nalezeno 5 záznamů.  Hledání trvalo 0.00 vteřin. 
Biodegradace 3D tištěných kompozitů na bázi poly(3-hydroxybutyrátu)
Gazdová, Nikol ; Menčík, Přemysl (oponent) ; Melčová, Veronika (vedoucí práce)
Tato bakalářská práce se zabývá biodegradací 3D tištěných těles složených z poly(3- hyroxybutyrátu), kyseliny polymléčné, biokeramiky a změkčovadla. Tyto složky byly vybrány pro svou biokompatibilitu a vlastnosti, které by mohly být využity v tkáňovém inženýrství jako dočasná, vstřebatelná náhrada kostní tkáně. Hlavním cílem bylo zkoumání vlivu jednotlivých složek těles na samotnou biodegradaci. Biodegradace probíhala při 37 °C v roztoku simulující iontovou koncetraci krevní plazmy. Vzorky byly postupně vytahovány v měsíčních intervalech po dobu pěti měsíců. Pro vyhodnocení výsledků byly použity 2 metody – změna hmotnosti a zkouška v tlaku, kde byla vyhodnocována pevnost jednotlivých těles. Z vyhodnocení dat nešlo dojít k jednotnému výsledku, která látka nejvíc ovlivňuje biodegradaci, protože vždy záleželo i na poměru látek ostatních. Pro zkoumaní vlivu poly(3-hydroxybutyrátu) a kyseliny polymléčné na rychlost biodegradace byly porovnávány směsi RP9, RP10 a RP15. Ukázalo, že vyšší zastoupení kyseliny polymléčné a nižší zastoupení poly(3-hydroxybutyrátu) výrazně pozitivně ovlivňuje rychlost biodegradace, jelikož rozdíl mezi poklesem hmotnosti pro směs RP9 s nejvyšším zastoupením poly(3-hydroxybutyrátu) a RP10 s nejvyšším zastoupením kyseliny polymléčné činil 8,37 % pro plné tělesa a 4,13 % pro tělesa porézní. U pevnosti to pak byl rozdíl o 73,32 % pro plné a 73,65 % pro porézní těleso. Při pozorování vlivu obsahu biokeramiky na směsích RP11, RP12 a RP15, jsme došli k závěru, že tento vliv je na rychlost biodegradace téměř zanedbatelný rozdíl poklesu hmotnosti mezi směsí RP11 s nejnižším obsahem biokeramiky a RP12 s nejvyšším zastoupením biokeramiky činil pouze 1,68 % pro plné tělesa a 0,99 % pro tělesa porézní, naopak směs RP15 se vykazovala nevyšší mírou biodegradace, přestože má střední hodnotu biokeramiky ve směsi. Pro mechanické vlastnosti to pak činí rozdíl o 10,4 % pro plné a 7,57 % u porézních těles. Při porovnání vlivu změkčovadla u směsí RP13, RP14 a RP15 byl zaznamenán vliv spíše na pokles pevnosti, kdy rozdíl v poklesu pevnosti u směsi RP13 s nejnižším obsahem změkčovadla a RP14 s nejvyšším obsahem změkčovadla byl rozdílný o 20,3 % pro plné a 18,16 % pro porézní těleso. Pokles hmotnosti pak byl rozdílný o 4,1 % pro plné a 0,83 % pro porézní tělěso. Jako důležitým faktorem pro rychlost biodegradace se nakonec stala biokeramika od rozdílných firem. Nejlépe se biodegradoval hydroxyapatit od firmy Applichem a nejhůře zase hydroxyapatit od firmy CN Lab. Rozdíl na pokles hmotnosti činil 17,35 % pro plné a 5,93 % pro porézní těleso. Úbytek pevnosti pak byl rozdílný o 55,6 % pro plné těleso a o 33,38 % pro porézní těleso.
Evaluation of the quality of polethylene terephtalate flakes for the production of food grade recycled regranulate
Snopková, Martina ; Melčová, Veronika (oponent) ; Kučerík, Jiří (vedoucí práce)
Polyethylene terephthalate (PET) is a widely used plastic, especially to produce PET bottles. However, waste PET bottles pose an environmental risk if they are not well managed. Recycling is an appropriate way to treat PET bottles, ideally by recycling them back into PET bottles. Nevertheless, recycling PET into food-grade recycled PET is challenging and the resulting quality is heavily dependent on the quality of the feedstock, i.e., the PET flakes. This thesis aimed to evaluate the quality of food-grade PET flakes on the EU market. Although the quality of PET flakes has already been the subject of several scientific studies, the analysis of the qualitive parameters of PET flakes has never been applied to such a large area as is the EU market. However, extensive analysis is essential for trend mapping and possible quality optimisation. For the analysis, material from different areas of the EU collected over a period of two years was used. The quality assessment included the quality control methods set out in EN ISO standards and standard operating procedures (SOPs), as well as spectrophotometry, Fourier-transform infrared spectroscopy – Attenuated total reflection (FTIR-ATR), and measurement of intrinsic viscosity. The suitability of each supplier and trends across the batches delivered were assessed. The most important findings included (1) other plastics content is the most problematic quality parameter of PET flakes, (2) other plastics content originates mainly from bottles and is independent of the collection system, (3) a higher degradation rate of PET flakes supplied by Western producers compared to the material from producers located in the East of the EU. A comprehensive analysis of the EU market and quality trends in PET bottle recycling by geographical area and type of collection system were provided. These results will not only be useful for practice, but they could also provide an incentive to improve legislation on the assessment of plastic contaminants or the introduction of more appropriate PET bottle design.
Mechanisms and kinetics of poly(3-hydroxybutyrate) reactions
Melčová, Veronika ; Sedláček,, Tomáš (oponent) ; Bakoš, Dušan (oponent) ; Přikryl, Radek (vedoucí práce)
This thesis deals with melt reactions of bacterial biopolymer poly(3-hydroxybutyrate) with selected reactive agents. Compounds of different functional groups; isocyanates, carbodiimides, alcohols and epoxides; and functionalities; from two to polyfunctional; were exploited. The aim is to characterize the kinetics of the polymer's thermal degradation during processing with and without the addition of aforementioned reagents in different dosages. For that, rheological measurement consisting of four subsequent frequency sweeps covering a range of 0.1–50 Hz was carried out and obtained data were evaluated to gain a viscosity loss rate. This kinetic parameter enabled the comparison of the effects of individual reagents. Moreover, reactive samples were prepared by kneading, where melt torque was recorded and discussed, and also by solution method, where solution viscosity was measured. The thermal properties, molecular weight and infrared spectra of such prepared samples were studied. Among the tested additives, polymeric carbodiimide Raschig 9000, hexamethylene diisocyanate, poly(glycidyl methacrylate) synthetized for the purpose of this work, and poly(hexamethylene diisocyanate) showed the best overall results in performed experiments. Notably, the sample with a 100-fold molar overdose of Raschig had a 20–30% lower value of the viscosity loss factor than the reference in the frequency region 0.1–5 Hz. In addition, an enzymatic biodegradability test with lipase and in abiotic conditions was carried out. Poly(3-hydroxybutyrate) additivated with poly(glycidyl methacrylate) showed the highest rate of molecular weight decrease.
Modification of polymer blends based on polyhydroxybutyrate and their properties
Melčová, Veronika ; Tocháček, Jiří (oponent) ; Přikryl, Radek (vedoucí práce)
Theoretical part of this work describes properties and modification possibilities of poly(3-hydroxy butyrate) (PHB) and amorphous poly(lactic acid) (PLA) and their blends. In experimental part, reactivity of Joncryl, Raschig, and phosphite reagents triphenyl phosphite, tris(nonylphenyl) phosphite, and diphenyl isodecyl phosphite with neat PLA and PHB are studied. Raschig, an oligomeric polycarbodiimide based additive, was proven to enhance melt viscosity of both polymers in amount 2%wt., therefore was used for preparation of blends in five PHB/(PHB+PLA) ratios. Samples with Raschig and corresponding non-reactive samples were studied using rheology, gel permeation chromatography and modulated differential scanning calorimetry. Results showed possible reaction of Raschig and PHB/PLA blends leading to branched structures. However, the rate of reaction is not sufficient to completely compensate decrease in viscosity due to processing degradation. Thus, non-reacted amount of Raschig remains in matrix. On the basis of these findings, it is concluded that Raschig behaves rather as a relatively effective stabilizer of rheological properties than as a reagent for the intentional modification of PHB/PLA blends’ structure. In order to study mechanical properties of these blends, samples plasticized with acetyltributylcitrate were prepared using twin screw extruder.
Modifikace polyhydroxybutyrátu roubováním funkčních skupin
Melčová, Veronika ; Tocháček, Jiří (oponent) ; Přikryl, Radek (vedoucí práce)
Předložená bakalářská práce se zabývá charakterizací vlivu chemické úpravy na termické a mechanické vlastností poly(3-hydroxybutyrátu). Pro studium byly vybrány dvě metody, a to chlorace a fluorace PHB. Cílem teoretické části práce bylo vytvořit ucelenou literární rešerši obsahující základní informace o polyhydroxybutyrátu a nejnovější poznatky o možnostech chemických úprav tohoto polymeru. Obsahem experimentální části je samotná chemická úprava materiálu, dále příprava vzorků k měření a provedení vybraných analýz. Chemicky roubované polymery byly podrobeny termogravimetrické analýze za účelem stanovení jejich termické stability. Pomocí diferenční kompenzační kalorimetrie byly sledovány entalpické změny v materiálu. Také byla sledována neizotermní krystalizace vzorků za účelem zhodnocení vlivu naroubovaného atomu halogenu na nukleační aktivitu polymeru. Vybrané vzorky byly podrobeny také dynamickomechanické analýze a tahové zkoušce.

Chcete být upozorněni, pokud se objeví nové záznamy odpovídající tomuto dotazu?
Přihlásit se k odběru RSS.