TY - GEN TI - Možnosti využití 3D laserového skenování v geotechnické praxi TT - Possibilities of using 3D laser scanning in geotechnical practise T3 - Podzemní stavby Praha 2019 AU - Kukutsch, Radovan AB - S pronikáním moderních a smart technologií se setkáváme ve všech odvětvích lidské činnosti, oblast hornictví a geotechniky nevyjímaje. Jednou z těchto technologií je i 3D laserové skenování, které za posledních deset let zaznamenalo výrazný technologický pokrok a stalo se nedílnou součástí monitoringu podzemních staveb jako nástroj umožňující komplexní, přesné a nezkreslené zachycení prostorové situace do digitální podoby. Právě tato skutečnost stála za tím, že je od r. 2013 3D laserový skener využíván pracovníky Ústavu geoniky AV ČR, v.v.i. jako nezbytná součást geotechnického a geotechnického monitoringu důlních děl, kdy lze oproti tradičním, zavedeným měřičským metodám, velmi přesně detekovat a kvantifikovat časoprostorové změny vyvolané zásahem člověka do horninového masivu. Nosným projektem posledních let byl monitoring napěťodeformačního stavu horninového masivu při dobývání 30. sloje v rámci zkušebního provozu dobývací metody Room and Pillar (chodba-pilíř) v ochranném pilíři jam Dolu ČSM, kde vedle mnoha jiných měřicích instrumentů bylo 3D laserové skenování využíváno pro konvergenční měření chodeb, zejména ale pro zachycení veškerých deformačních změn na ponechaných pilířích. Doplňkovou funkcí bylo komparativní hodnocení s výsledky jiných nástrojů, kupř. s údaji naměřenými pomocí horizontálních extenzometrů. Předmětem příspěvku tak bude všeobecné vytyčení možností uplatnění 3D laserového skenování v geotechnické praxi, a to na prostorových datech pořízených během monitoringu trvajícím bezmála 3,5 roku, kdy byly na Dole ČSM zachyceny významné fenomény v pohybu stěn pilíře a vyzvedávání počvy v řádu desítek cm, místy až 100 cm. AB - We are experiencing the penetration of modern and smart technologies in all sectors of human activity, including mining and geotechnics. One of these technologies is 3D laser scanning, which has seen significant technological advancements over the last decade and has become an integral part of underground construction monitoring as a tool to enable comprehensive, accurate and unbiased capture of the spatial situation in digital form. This development was behind the fact that since 2013, 3D laser scanner has been used by the Institute of Geonics of the Czech Academy of Sciences as a necessary part of the geotechnical monitoring of mine works, when it is possible to precisely detect and quantify the time-space changes caused by man's intervention in the rock mass compared to the traditional established measuring methods. A leading project of recent years was the monitoring of the strain stress state of the rock massif during the 30th seam extraction during the trial operation of the Room and Pillar extraction method in the CSM Mine shaft safety pillar where, besides many other measuring instruments, 3D laser scanning was used for the convergence measuring of roadways, especially for capturing any deformation changes on the permanent pillars. A complementary function was the comparative evaluation with the results of other tools, e.g. with data measured by horizontal extensometers. The subject of the article will be a general description of the possibilities of using 3D laser scanning in geotechnical practice on spatial data acquired during the monitoring lasting almost 3.5 years, when important phenomena were detected in the movement of the pillar walls and the floor heave in the CSM Mine in the tens of cm, sometimes up to 100 cm. SN - 978-80-906452-3-3 UR - http://www.nusl.cz/ntk/nusl-396529 UR - http://hdl.handle.net/11104/0296944 A2 - Kajzar, Vlastimil A2 - Waclawik, Petr A2 - Šňupárek, Richard LA - cze KW - roadways deformation KW - 3D laser scanning KW - room and pillar PY - 2019 PB - Ústav geoniky, Studentská 1768 , 708 00 Ostrava - Poruba, http://www.ugn.cas.cz/ ER -