Institute of Plasma Physics

Latest additions:
2024-04-01
22:21
Vytyčení směru vývoje pro analýzu optických cest
Pintr, Pavel
Výzkumná zpráva obsahuje výběr objektivů pro stereoskopické snímání ve vysokém rozlišení, přehled vad skel a průzkum trhu průhledového okénka.

Detailed record
2024-02-18
00:07
Ceramic protection of anti-corrosion layers of 3-glycidyloxypropyl-triethoxysilane on steel
Pokorný, P. ; Janata, Marek ; Brožek, Vlastimil
There are various variations on the problem of steel reinforcement bond strength in concrete. Along with geometrical considerations, corrosion performance of steels with varying chemical compositions in interaction with variable chemical compositions of concrete are crucial. One approach is to cover steel surfaces with organosilane compounds, which increases the reinforcement resistance to corrosion in both acidic and alkaline conditions but, on the other hand, may weaken the reinforcement bond strength on concrete. The issue is resolved by intentionally forming a thin-walled, highly adhering corundum layer that is highly porous and impregnated with 3-glycidyloxypropyltriethoxysilane. This procedure also includes testing the adhesion properties between the ceramic and the metal and the cement prior to conducting a corrosion test in a chloride environment.

Detailed record
2023-12-17
00:02
Ceramic protection of anti-corrosion layers of 3-glycidyloxypropyl-triethoxysilane on steel
Pokorný, P. ; Prodanović, N. ; Janata, Marek ; Brožek, Vlastimil
There are various variations on the problem of steel reinforcement bond strength in concrete. Along with geometrical considerations, corrosion performance of steels with varying chemical compositions in interaction with variable chemical compositions of concrete are crucial. One approach is to cover steel surfaces with organosilane compounds, which increases the reinforcement resistance to corrosion in both acidic and alkaline conditions but, on the other hand, may weaken the reinforcement bond strength on concrete. The issue is resolved by intentionally forming a thin-walled, highly adhering corundum layer that is highly porous and impregnated with 3-glycidyloxypropyltriethoxysilane. This procedure also includes testing the adhesion properties between the ceramic and the metal and the cement prior to conducting a corrosion test in a chloride environment.

Detailed record
2023-01-29
22:31
Preparation of W-Cu composites by infiltration of w skeletons review
Matějíček, Jiří
Tungsten-copper composites feature high corrosion and erosion resistance, very good thermal and electrical conductivity, low thermal expansion and good mechanical properties. They are used in a variety of demanding applications, such as arc-resistant electrodes, high voltage electrical contacts, heat sinks for integrated circuits, etc. They are also foreseen for use in plasma-facing components of fusion reactors, e.g. as a transition layer between the (refractory) plasma-facing tungsten and the (highly conductive) copper-based cooling structure. In general, high density and good bonding of the tungsten and copper phases is desired. Molten copper infiltration into tungsten preforms is among the prospective fabrication technologies - the structure and properties of the resultant composites are dependent on the specific technological parameters. In this paper, the preparation of W-Cu composites by infiltration of W skeletons is reviewed and attention is paid to the influence of these particular parameters: infiltration temperature, time and atmosphere, tungsten preform porosity, orientation and chemistry (presence or absence of other elements). Optimum parameter combinations for achieving high density and proper bonding of copper and tungsten are identified.

Detailed record
2023-01-08
22:31
Composite coatings containing nanometric constituents prepared by plasma spraying with liquid feedstocks
Mušálek, Radek ; Tesař, Tomáš ; Medřický, Jan ; Čížek, Jan ; Lukáč, František
Plasma spraying of liquid feedstocks allows deposition of materials with novel microstructures. Due to the combination of a liquid carrier and ultrafine powders (in case of suspensions) or in-situ formation of the final material in the plasma jet (in case of solutions), preparation of ultrafine composites is possible, typically in a form of coatings on the substrates. Moreover, both suspension and solution spraying routes can be easily combined, either together or even with conventional plasma spraying of coarse dry powders, thus merging benefits of “nanometric” and “micrometric” constituents in the final composite microstructure. As a consequence, liquid feedstock plasma spraying represents an industrially-relevant deposition process with wide variability, providing coatings with properties tailored for various applications ranging from compact wear-resistant layers, porous thermal barrier coatings, bio-compatible medical coatings, catalyst carriers, fuel-cells, etc. The paper introduces several examples of such ultrafine coatings recently deposited at IPP CAS using hybrid water-stabilized plasma torch.

Detailed record
2023-01-08
22:31
High temperature corrosion behaviour of nicr-based coatings applied by twin wire arc spray technology
Lencová, K. ; Vostřák, M. ; Naďová, J. ; Lukáč, František ; Mušálek, Radek
High temperature corrosion is a serious problem related to the combustion of heavy oils with high vanadium contents. Protective overlay coatings are used to allow functioning of engineering components under extreme conditions and provide corrosion resistance to extend the component life. This article is concerned with the high temperature corrosion behaviour of two protective NiCr-based coatings and bare structural steel 1.4959 (W.nr.) in a molten salt environment of 40% Na2SO4 and 60% V2O5 at 750 °C under cyclic condition. NiCr and NiCrMoNbTa coating was deposited on steel 1.4903 (W.nr.) by Twin wire arc spray technology (TWAS). To establish the kinetics of corrosion, the thermogravimetric technique was used. The X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) techniques were used to analyse the corrosion products and determine the corrosion mechanism. The hot corrosion resistance of both coatings was better than bare steel samples. The NiCrMoNbTa coating showed better corrosion behaviour than the NiCr coating. However, also the NiCr coating provides sufficient protection to the substrate material.

Detailed record
2022-09-28
00:47
Design of experimental device for testing of subcooled flow boilling
Gleitz, M. ; Zacha, P. ; Entler, Slavomír ; Syblík, J.
The article presents the principle and function of the Hypervapotron and the current work progress on the realisation of the experimental loop. Hypervapotron is a heat exchanger operating in a two-phase flow regime, in which the latent heat of the water/steam phase transformation is used, which enables the transfer of large heat fluxes (up to tens of MW/m(2)). For this reason, it appears to be very promising for use in fusion reactors. The article describes the steps leading to the final design of the experimental loop selection of suitable mesh parameters in the Star-CCM+ code, geometry and used materials of the single elements of the heating system using electromagnetic induction. The effort of the experimental loop and the flow study in the Hypervapotron in general, is dimensional and material optimization of the geometry is suitable for a wide range of applications for which the benefits of subcooled boiling and Hypervapotron geometry can be applied.

Detailed record
2022-09-28
00:47
Microstructure and microhardness evaluation for NiCrAlY materials manufactured by spark plasma sintering and plasma spraying
Hulka, Iosif ; Mušálek, Radek ; Lukáč, František ; Klečka, Jakub ; Chráska, Tomáš
NiCrAlY deposited by different thermal spraying methods is commonly used as the bond coat material in thermal barrier coatings (TBCs). In the present study, two experimental coatings were deposited by hybrid water stabilized plasma (WSP-H) and radio frequency inductively coupled plasma (RF-ICP) using the same feedstock powder. Spark plasma sintering (SPS) was used to manufacture a compact NiCrAlY from the same feedstock powder as a reference material. Microstructure, internal oxidation, phase characterization and quantification of the mechanical behaviour in terms of microhardness were studied. The investigations clearly showed microstructural and mechanical differences between the NiCrAlY samples manufactured by different plasma technologies. The results confirmed that SPS and RF-ICP provide dense structures with no oxides due to the fabrication under protective atmosphere and similar mechanical properties. Thus, RF-ICP may be used for deposition of very dense coatings with microstructure and hardness comparable to compacted materials prepared by SPS.

Detailed record
2022-09-28
00:47
Bakerova širokoúhlá fotografická komora s paraboloidickým zrcadlem
Rail, Zdeněk ; Melich, Zbyněk ; Šrajer, Bohdan ; Vápenka, David ; Tomka, David ; Thoř, Tomáš ; Pintr, Pavel ; Macner, David
Zorné pole paraboloidického zrcadla je malé. Dominantní vada, která omezuje jeho úhlový průměr, je koma. Pomocí systémů čoček a asférických desek je možné u zrcadlových systémů mimoosové obrazy hvězd opravit a zorná pole zvětšit. V této práci předkládáme návrh takové fotografické komory, spočtené Jamesem G. Bakerem. Jeho fotografický přístroj se skládá z paraboloidického zrcadla, tmeleného dubletu před ohniskem a z asférické korekční desky, umístěné ve vstupním paralelním svazku před soustavou.

Detailed record
2022-09-28
00:47
Zbytkové vady Gajduškova objektivu o průměru 200 mm a ohniskové vzdálenosti 3480 mm Hvězdárny a planetária v Hradci Králové
Rail, Zdeněk ; Melich, Zbyněk ; Šrajer, Bohdan ; Vápenka, David ; Tomka, David ; Thoř, Tomáš ; Macner, David
Achromatický dublet o průměru 200 mm a ohniskové vzdálenosti 3480 mm byl vyroben profesorem ing. Vilémem Gajduškem v Ostravě v roce 1954. Dalekohled s tímto objektivem je umístěn na Hvězdárně a planetáriu v Hradci Králové. Objektiv byl v roce 2018 restaurován v Ústavu fyziky plazmatu, v.v.i.-Centru Toptec v Turnově. Čočky byly přeměřeny a z naměřených hodnot jsme vyčíslili jeho zbytkové optické vady. Výsledky simulace přinášíme v této práci.

Detailed record